|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
February 16, 2009, 09:00 PM | #1 |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
My next modification to my Lil Pietta
The Cylinder Pin.
I had been wanting to do this mod since I got this little jewel but finally gotten my self around to getting a few new pins for it & bringing my self to do it. The job was simple really. Taken my new pin, marked in 2 locations where I wanted it to hinge at & used my dremel with a medium cutting disk "to make the smallest cut" & cut the pin at a 45* angle. Then I marked the cut ends for a center cut to accept my home made link & used the heavy duty cut disk for this "since my link was just a bit thicker than the disk. Using a 1/4" X 2" body washer as my material for my link I cut & drilled it to match what I wanted, then drilled the pin to accept a 5/64" roll pin. Assembled the pin, some minor filing to get the roll pins the same profile as the rest of the pin & then used a single coat of Oxpho-Blue to protect my work. Here is my result after about 1 hour of work. |
February 17, 2009, 11:41 AM | #2 |
Member
Join Date: December 23, 2008
Posts: 60
|
OK, I have to ask
Why?
What purpose does this serve? |
February 17, 2009, 12:02 PM | #3 | |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
Quote:
|
|
February 17, 2009, 02:10 PM | #4 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
An alternate fix
Raider,
Did you every think of hinging the barrel instead of the rod? Just kidding!
__________________
Seek truth. Relax. Take a breath. |
February 17, 2009, 02:43 PM | #5 |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
Yeah I did think of that He He but just the thought of a huge Bolt on the side of the frame didn't appeal to me.
|
February 17, 2009, 06:03 PM | #6 |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
New pictures.
What do y-all think? |
February 17, 2009, 08:48 PM | #7 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Well
Raider,
You could have made the barrel longer, say about 7.5 inches. Then the rod would come out far enough to take the cylinder all the way out. OKay...Okay I couldn't resist. On the serious side. Just looked at the photos I do like the looks of the job. Did you do any touch up bluing? It appears as though the finish has not been touched with a cutting tool.
__________________
Seek truth. Relax. Take a breath. |
February 17, 2009, 09:00 PM | #8 |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
Yeah Doc I used Oxpho-Blue to reblue it once I was done.
|
February 17, 2009, 10:08 PM | #9 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Thanks
Raider,
Thanks for the heads-up.
__________________
Seek truth. Relax. Take a breath. |
February 18, 2009, 07:41 AM | #10 |
Junior Member
Join Date: August 6, 2008
Location: Anywhere but here
Posts: 13
|
Nice work!
|
|
|