The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old May 12, 2011, 07:30 PM   #1
chasep255
Senior Member
 
Join Date: December 21, 2009
Location: NJ
Posts: 727
.223 Loaded with 55gr FMJ and 24.5gr H335 Velocity?

I am not going to get a chance anytime soon to chrony these loads I made so I am just wondering if anyone else has data on this load using an AR with a 20'' barrel.
chasep255 is offline  
Old May 12, 2011, 08:15 PM   #2
rg1
Senior Member
 
Join Date: November 6, 2001
Posts: 1,125
-- Colt 1/7 20" AR--RP 7 1/2 primer--RP and WCC cases
-Hornady 55 fmj seated to 2.218-2.220"
-H 335 powder
-July 90 degrees
-Oehler 35 P at approx. 10 ft
___________
average velocities
23.2--2850fps
24----2975-3005fps
24.5---3050-3080fps
Maximum as per Hodgdon--25.3 -----3165-3195fps
These loads as mentioned are in a 1/7 Colt 20" rifle. Your loads may vary in your rifle but I wouldn't think by much and your components may cause some variation. Work up to the maximum load in your rifle with your components. But 24.5 grains with Hornady 55 fmj's and H335 should be safe. A lot of AR shooters use 25 grains and report it to be accurate. That's what I've settled on and shoot these loads in different AR's 1/9 and 1/7 twist and 16 and 20" barrels. Don't know which 55 fmj you're loading but that may make some difference too and your overall length may make a little difference. Hornady 55 fmj's have a blunter tip and overall lengths are 2.200-2.230" while sharply pointed military style 55 fmj's are most often seated to 2.250" oal.

Last edited by rg1; May 12, 2011 at 08:22 PM.
rg1 is offline  
Old May 12, 2011, 09:37 PM   #3
chasep255
Senior Member
 
Join Date: December 21, 2009
Location: NJ
Posts: 727
Thanks. I just wanted to get an idea (withing an 100 FPS of accuracy) as to how fast my bullets are going.
chasep255 is offline  
Old May 12, 2011, 10:52 PM   #4
Miata Mike
Senior Member
 
Join Date: May 22, 2010
Location: North East WI
Posts: 418
Kind of nice to know. I have been loading at 25 grains and using a military 55 grain fmj. No signs of over pressure at all, but sounds like it is getting a bit on the hot side if some heavy brass slips through.
Miata Mike is offline  
Old May 13, 2011, 12:48 AM   #5
medalguy
Senior Member
 
Join Date: August 31, 2009
Location: New Mexico
Posts: 1,033
Right on the money. I also load 5.56 Hornady 55 gr for my rifle and I get right at 3000 fps with that load in H335 at 2.235 COAL.
medalguy is offline  
Old May 13, 2011, 06:31 AM   #6
Qtiphky
Senior Member
 
Join Date: December 11, 2008
Location: Upper Michigan, above the Mackinac Bridge
Posts: 568
I am loading 23.6 grains of H335 with a 55 grain bullet shooting out of my Bushmaster and I am getting 2836 fps. This is an extremely accurate load out of my gun and I wanted accuracy more than I needed more velocity.
Qtiphky is offline  
Old May 13, 2011, 10:09 AM   #7
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
CAUTION: The following post includes loading data beyond currently published maximums for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The Firing Line, nor the staff of TFL assume any liability for any damage or injury resulting from use of this information.

55 gr H335 .223 has a threshold of long brass life between 29 and 30 gr.

This is much higher than published loads because the .223 was SAAMI registered at 55kpsi, but can run more than 75kpsi.

It has 10X the loose primer pocket safety margin per SAAMI registration of 270W, 6mmRem, or 22-250Rem.
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Old May 13, 2011, 01:22 PM   #8
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 21,022
CAUTION: The following post includes loading data beyond currently published maximums for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The Firing Line, nor the staff of TFL assume any liability for any damage or injury resulting from use of this information.

.223 started with a 52K CUP MAP from SAAMI. It was revised to 55K PSI MAP by conformal piezo transducer, in one of the more curiously wimpy conversions. I once looked through all the other SAAMI cartridges I could find that started at 52K CUP, and all are now in the range of 60K-65K PSI MAP by transducer. Average is not quite 62K PSI MAP, as I recall. I don't know what went wrong with the .223, but the European CIP has it as 430 MPa (62,366 PSI), and that's worked for them and for NATO so that's the limit I use. If you buy European made ammo, ever, so do you.

As Clark says, many guns can go higher, but throat erosion rates can increase dramatically above the mid-60's, so I elect to stay inside the CIP numbers as best I can.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old May 14, 2011, 09:41 AM   #9
bkhann
Member
 
Join Date: August 5, 2009
Location: Grand Rapids MI
Posts: 98
I just recently did a load development using H335 and 55 gr FMJBT bullets in .223. COL was 2.200”. These are the results:
23.5 gr 2762 fps
24.0 gr 2817 fps
24.5 gr 2882 fps
25.0 gr 2941 fps
25.5 gr 2977 fps
26.0 gr 3032 fps
26.5 gr 3081 fps
To my surprise the best accuracy and grouping was attained with the 23.5 gr load.
bkhann is offline  
Old May 15, 2011, 12:39 PM   #10
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 4,678
I know from experience that hot H335 loads in 223 have a way higher point of impact on the target at 200 yards than IMR4895 loads. I don't know if that was trajectory or recoil.
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Old October 28, 2012, 02:27 AM   #11
XxBulletBendeRxX
Junior Member
 
Join Date: February 7, 2012
Location: Way out West, The Wild We
Posts: 11
Great thread guys... thx for the info.. Im loading a few right now.. i am trying 24.3 grains of h335 with a military 55 grain fmj. i want accuracy but dont need sub moa at 100+ yards as this is just going to be blasting/plinking ammo. Ive tried the 25 grains 55 gr fmj with a oal of 2.230 and it is good vs cans and 4 ich clays at 50-80 yards, but on paper not he tightest groups. so Im lowering the charge just a little to 24.3 grains h335 to hopefully tighten it up a little more. will verify on paper, im also going to try 24.6 and 24.8 grains and see what I get... . ALso going to lthrow a few varget loads with 75 grainers for the 1/7 twist Adams upper, but hats irrelevent to topic just thought id share... Well, Back on the press,

XxBulletBendeRxX
XxBulletBendeRxX is offline  
Old October 28, 2012, 02:29 AM   #12
XxBulletBendeRxX
Junior Member
 
Join Date: February 7, 2012
Location: Way out West, The Wild We
Posts: 11
^^^ NOT TO MENTION ressurect this old thread... ^^^
XxBulletBendeRxX is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.08391 seconds with 10 queries