The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Lock and Load: Live Fire Exercises

Reply
 
Thread Tools Search this Thread
Old September 17, 2021, 02:35 PM   #1
Pistoler0
Senior Member
 
Join Date: November 15, 2019
Location: Conifer, CO
Posts: 570
How accurate are ammo manufacturer's claimed MV numbers?

I don't have access to a chronometer, and I am trying to develop DOPE for my 308 bolt action. I have about 500 rds of SMK loaded ammo (Bullets 1st) which is accurate and affordable. They quoted velocity out of an 18" AR-10 barrel which is difficult to extrapolate to my 26" bolt action barrel.

I am also trying to devise a drop chart for an AR-47 that I mostly feed with Tula.

In your experience, how accurate are ammo manufacturer's claimed MV numbers?

I suppose this vary by manufacturer, and in that case I would appreciate your experience with the factory ammo that you are familiar with.
__________________
Life is simply an inter-temporal problem of constrained optimization.
Pistoler0 is offline  
Old September 17, 2021, 02:49 PM   #2
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 8,681
They are very accurate for the barrel, component lots and technique used. The same ammo won't shoot the same speed in other barrels.

Your load will change about 25 fps per inch of the barrel length.
Bart B. is offline  
Old September 17, 2021, 03:10 PM   #3
Pistoler0
Senior Member
 
Join Date: November 15, 2019
Location: Conifer, CO
Posts: 570
Quote:
Originally Posted by Bart B. View Post
Your load will change about 25 fps per inch of the barrel length.
Thank you, this is useful info.
__________________
Life is simply an inter-temporal problem of constrained optimization.
Pistoler0 is offline  
Old September 17, 2021, 04:17 PM   #4
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 8,681
Here's some icing on this conversation cake.

Rarely will two people shooting the same rifle and ammo get the same velocity.
Bart B. is offline  
Old September 17, 2021, 05:15 PM   #5
jmr40
Senior Member
 
Join Date: June 15, 2008
Location: Georgia
Posts: 10,440
There have been countess tests done and data posted on the internet where people have measured velocity, cut the barrel down 1" and repeated until they got to the legal minimum. The velocity difference is usually a lot less than most think, especially with common barrel lengths.

http://bulletin.accurateshooter.com/...s-with-length/

https://rifleshooter.com/2015/01/308...ld-medal-bthp/

The problem is that even from the same barrel length you will see very different speeds from different barrels. Around 25-50 fps is normal and I've seen some cases where there was 100fps difference between 2 different rifles with barrels the same length.

I have a 308 with a 20" barrel that shoots faster than either of my 22" rifles. And there is 20-30 fps difference between each of the ones with 22" barrels. My 22" Winchester 30-06 is consistently 60-90 fps faster than my 22" Remington 30-06.

Even if you were working with load data for a 26" barrel it wouldn't necessarily be accurate for YOUR 26" barrel.

In your case I'd take the speeds from the 18" barrel and add about 100 fps to it and run the numbers. That should be close enough to get you on paper with your shots. You can tweak things from there.
__________________
"If you're still doing things the same way you were doing them 10 years ago, you're doing it wrong"

Winston Churchill
jmr40 is offline  
Old September 18, 2021, 01:10 AM   #6
stagpanther
Senior Member
 
Join Date: March 2, 2014
Posts: 9,473
I find quality manufacturer's quotes to be very close, sometimes right on, even if I don't know what barrel they used. Hornady's stuff for example.
__________________
If you’re ever hiking in the woods and you get lost, just look up and find the brightest star in the sky and you’ll know which way space is.
I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk!
stagpanther is offline  
Old September 19, 2021, 11:42 AM   #7
Lavan
Senior Member
 
Join Date: December 10, 1999
Location: California
Posts: 2,625
http://www.ballisticsbytheinch.com/calibers.html



Whoops seem only handguns. oh well
Lavan is offline  
Old October 26, 2021, 06:57 PM   #8
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 6,734
Kind of a long story but keeping it short, I had occasion to test 5 lots of 270 Winchester. 130 to 150 grain. I was using a LabRadar.

All were a bit higher for listed velocity. My barrel is 26 inches so that is longer than the old standard of 24 and what seems to be the new standard of 20.
__________________
Science and Facts are True whether you believe it or not
RC20 is offline  
Old October 27, 2021, 02:52 AM   #9
Seedy Character
Senior Member
 
Join Date: July 5, 2021
Location: SW Okla
Posts: 201
Without a chrony, you are guessing.
Seedy Character is offline  
Old October 27, 2021, 02:23 PM   #10
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 12,802
Some manufacturers are pretty close to 'average' with their advertised velocities. Some are way off, because they're advertising their best numbers from a test barrel.
In my experience, Nosler and Federal tend to hype the numbers. And most "hyper" or "ultra" velocity branding is going to be optimistic. Hornady Superformance is one that fits there.

Quote:
Your load will change about 25 fps per inch of the barrel length.
This "rule of thumb" is never right.
I have never seen this be even remotely correct for barrels that I have cut.

Is it a reasonable baseline for expectations when cutting a barrel?
Maybe. For 'standard length' barrels, shooting certain cartridges.
But it is never right on the money, and has no chance of being realistic if the barrel is unusually long, or starting 'short'.

If you want to know what the muzzle velocity is from your barrel, you need to buy a chronograph or find someone that will let you use theirs.

I have had many experiences like jmr40's.
In one 'outlier' case, I maintained the same velocity from a .270 Win barrel after cutting it from 22 to 19 inches. (Same ammo, before and after. Six loads tested, I believe.)
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04576 seconds with 10 queries