The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Reply
 
Thread Tools Search this Thread
Old May 11, 2019, 04:19 PM   #26
Reloadron
Senior Member
 
Join Date: June 8, 2016
Location: Cleveland, Ohio Suburbs
Posts: 1,281
What was the ME and TE?

ME (Muzzle Erosion)
TE Throat Erosion

The ME and TE numbers are derived using a gauge. There are a variety of gauges available from various manufacturers. When a CMP rifle ships they include the gauge readings for the muzzle and throat of the rifle you get. Here is one such example and explanation: The Infamous Throat Erosion Gage.

Never mind, being slow on the uptake I figured out you wanted the actual numbers. Duh!

Ron
Reloadron is offline  
Old May 12, 2019, 09:18 AM   #27
agtman
Senior Member
 
Join Date: July 26, 2001
Location: midwest
Posts: 2,142
Quote:
lunger: If asking about my special, Has new barrel. So zero and zero.
Your new Criterion barrel will for sure not disappoint, provided you hold up your end of the marksmanship equation. Remember, 'it's the singer, not the song.'

That said, experienced M1-users will tell you that of the three criteria for judging what might be called the 'shoot-ability' of a CMP USGI barrel - TE, ME, and MW - the last two are by far the most important.

While ME typically refers to the internal or interior wear on the barrel at the muzzle, MW is actually the condition of the crown. There, you're looking for imperfections like dings, dents, burrs, and 'saw' marks, which are telltale wear patterns from careless and repeated passes of the cleaning rod(s) by previous owner(s), typically soldiers. The rods have basically cut into the crown, which is final contact point for the bullet before it exits the barrel.

So on a given USGI barrel, you can have a relatively high TE number without accuracy being noticeably affected as long as the ME measures out on the low end and the condition of the crown is otherwise intact (MW).
agtman is offline  
Old May 12, 2019, 09:53 AM   #28
lunger
Senior Member
 
Join Date: May 17, 2007
Posts: 336
Good info thanks. I have purchased a muzzle protector to use while cleaning along with ratcheting chamber brush , and plastic chamber insert. May use bore snake for cleaning between sessions.

If in future I buy one with USGI barrel I will inspect as suggested.
lunger is offline  
Old May 13, 2019, 12:09 AM   #29
veprdude
Member
 
Join Date: March 18, 2019
Posts: 31
+1 on the bore snake. If you're shooting any non-corrosive ammo a bore snake is all you really need to clean 95%+ of the gunk out. No need to religiously clean the bore with a rod every range trip of 50 rounds.

Dirt, dust and burnt powder attracts moisture and rust. No gunk no rust.
veprdude is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:34 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04889 seconds with 11 queries