The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old August 8, 2017, 12:23 PM   #1
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
Need help with identity

Hello,

I found this revolver in an old trunk I've had for many years. I know it's a Remington. 1858 Converted? Another year? Whitney Navy Converted? I just can't figure it out.

Any ideas would be very helpful!
Attached Images
File Type: jpg 20170801_205938.jpg (144.5 KB, 79 views)
jcoers is offline  
Old August 8, 2017, 03:18 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 24,047
It is not a Remington; it certainly looks like a Whitney Navy, converted, probably to .38 rimfire. The cylinder is not percussion and the rammer has been removed. It could be an original which was converted in the post-CW era. But my instinct on seeing a revolver like that with missing parts is to suspect a "kit gun" that someone got tired of when it turned out not to be easy to complete.

IIRC, Whitney copies, like others, were/are sold as kit guns and conversion cylinders/hammers have been available. Similar brass frame "Confederate" revolvers have also been sold.

What markings are present? If there are none, or if there are any indications that it is a repro (like Italian proof marks), the issue of age is settled.

Jim
__________________
Jim K
James K is offline  
Old August 8, 2017, 06:27 PM   #3
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
Hello James,

The only markings I can find on the revolver are the serial number 10383 H B. It's on the frame under the trigger guard and on the trigger guard itself.

I agree, it appears to be a Whitney.
Attached Images
File Type: jpg WhitneyFrame.jpg (100.1 KB, 38 views)
jcoers is offline  
Old August 8, 2017, 06:33 PM   #4
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
Trigger Guard
Attached Images
File Type: jpg WhitneyTriggerGuard.jpg (235.8 KB, 36 views)
jcoers is offline  
Old August 9, 2017, 12:20 AM   #5
JohnKSa
Staff
 
Join Date: February 12, 2001
Location: DFW Area
Posts: 20,731
Is that a small crown stamped on the trigger guard between the forward screw hole and the serial number?
__________________
Did you know that there is a TEXAS State Rifle Association?
JohnKSa is offline  
Old August 9, 2017, 01:11 PM   #6
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
I've been trying to figure out if that mark is intentional or a tool mark. I sent photos to Dan Williams - he wrote a reference book on the Whitney Revolver a few years ago. I'm hoping he can shed some light on that mark.
jcoers is offline  
Old August 10, 2017, 12:25 PM   #7
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 39,043
It doesn't look like a tool mark, it looks like a casting mark.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 10, 2017, 04:15 PM   #8
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 14,077
The serial number with two letters is correct, The serial should also be on the bottom barrel flat and inside the grips. The top of the barrel should be marked E. Whitney N. Haven
Hawg is offline  
Old August 11, 2017, 10:23 AM   #9
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
I checked the serial number with Dan Williams. He said it's one of the lowest serial numbers he's seen on a conversion from Whitney. His book is supposed to arrive next week, so, hopefully I will know a lot more about this revolver soon.

The finish all over the pistol is so worn that I can't make out any stamping on the top flat of the barrel. The bottom flat, near the frame, shows the last three digits of the serial number and an "X". I'm looking closely for a "B" stamped on the frame near the barrel - that would be a military proof mark. The serial number, according to Dan, is within range for use as a Union Army pistol.

Hope to know more soon!
jcoers is offline  
Old August 11, 2017, 10:34 AM   #10
jcoers
Junior Member
 
Join Date: January 12, 2016
Posts: 9
The pistol belonged to my Grandmother's first husband. He traveled with Bill Cody's Wild West. Here's a picture of the revolver along with his saddle bags and hat.
Attached Images
File Type: jpg Whitley3Reduced.jpg (112.0 KB, 21 views)
jcoers is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2016 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05946 seconds with 10 queries