The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old April 23, 2017, 06:55 PM   #1
sixgunnin
Senior Member
 
Join Date: March 24, 2017
Location: Montana
Posts: 176
Vaquero grip interchangeability?

Do New Vaquero grips usually need fitting? I have read stories of factory grips that were not even close to fitting, is this something that people see with Ruger revolvers?

I am a bit scared of buying Ruger grips for that reason. Is it a concern?

I once handled a nib Blackhawk that had about a 1/16'' gap between the grip and the frame

I am looking for a set of factory checkered polymer grips to replace the Dooley Gang star grips.
sixgunnin is offline  
Old April 24, 2017, 08:40 AM   #2
CowTowner
Senior Member
 
Join Date: October 17, 2007
Location: Cowtown of course!
Posts: 1,736
While I don't have an answer to your question, I do think this thread would do better in the Smithy section.
Mods, perhaps you could move this?
__________________
NRA Chief Range Safety Officer, Home Firearms Safety, Pistol and Rifle Instructor
“Today, we need a nation of Minutemen, citizens who are not only prepared to take arms, but citizens who regard the preservation of freedom as the basic purpose of their daily life......” President John F. Kennedy
CowTowner is offline  
Old April 24, 2017, 12:03 PM   #3
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 9,927
Never had to 'fit' aftermarket grips for anything.
Ruger factory grips are made for Ruger by Altamont. According to their site. Slightly less expensive direct from Altamont too.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old April 24, 2017, 06:51 PM   #4
James K
Senior Member
 
Join Date: March 17, 1999
Posts: 24,384
This probably should be moved to the Smithy section, but it seems to have little interest, so let's leave it and see what happens.

Jim
__________________
Jim K
James K is offline  
Old April 24, 2017, 11:05 PM   #5
Tinbucket
Senior Member
 
Join Date: January 17, 2015
Posts: 355
vaquero grip interchangability

Interested my self on this one. I want to put modern mother of pearl on my stainless Vaquero.
I put ivory on my Super Blackhawk and they fit perfectly.
I took them off as the Pachymers are called for with heavy loads. If you are talking another pair from Ruger they should fit perfectly, as they are all ade on the same machinery.
I don't have Ruger's number handy but give them a call. I don't believe they are hand fitted except for perhaps a little burr or something.
Don't buy a pair that may be lemons someone is trying to get rid of.
Tinbucket is offline  
Old April 25, 2017, 12:44 AM   #6
shootniron
Senior Member
 
Join Date: April 16, 2011
Location: Georgia
Posts: 1,600
Grips for Ruger guns interchange very well as long as you make sure that you have matched the grips to the grip frame. Different models of Ruger revolvers can have different grip frames. If the grips match the grip frame...there is normally no fitting required...however, some grips will matchup better than others...but, they will fit and be functional with no problem.

There is one caveat to this...if you happen to have a gun with the lock...it requires grips with a relief cut in the grips.

This is a pretty thorough explanation of all of the Ruger grip frames...will give you an idea of what you will need to fit your gun.

http://www.gunblast.com/Hamm_Ruger-SA-GripFrames.htm

Last edited by shootniron; April 25, 2017 at 12:50 AM.
shootniron is offline  
Old April 27, 2017, 09:38 AM   #7
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 14,726
Quote:
Never had to 'fit' aftermarket grips for anything.
You never tried to put grips on an Italian black powder revolver then. They finish the grips and grip frame together so no two sets of grips will swap. As for the New Vaquero any grips made for the New Vaq will fit but other Ruger models will not. On the other hand grips for the old Vaquero fit everything except the Super Blackhawk and New Vaq. Check out these grips. You may find something you like. https://www.altamontco.com/pistol-gr...er/newvaquero/
Hawg is offline  
Old April 27, 2017, 12:54 PM   #8
Tinbucket
Senior Member
 
Join Date: January 17, 2015
Posts: 355
How can I tell if this is the new or old Vaquero.
I bought it circa 1996. It has the horrible stamping on the barrel and frame but does not say new anywhere.
Tinbucket is offline  
Old April 27, 2017, 03:15 PM   #9
sixgunnin
Senior Member
 
Join Date: March 24, 2017
Location: Montana
Posts: 176
It is an old Vaquero
sixgunnin is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05843 seconds with 8 queries