The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Thread Tools Search this Thread
Old April 12, 2018, 10:29 PM   #1
Junior Member
Join Date: November 27, 2014
Location: Georgia
Posts: 7
Type 99 long rifle wood restoration

At my local gun store I found an old beat-up type 99 tucked away on the rack. As a collector of milsurps and not having a jap rifle, i haggled them to 150 and walked out with it.

My love with mil surps is cleaning them up and showing them some love. I replace parts when necessary but i prefer to keep them original. The rifle had light rust over the body woth a perfect bore. The stock was the worst part: it had dings and a large crack on the front left that had been shoddily repaired with wood glue. The over all shape was curved as if the wood had been warped at some point. There were also 2 pins in the grip from previous repair

When i got home i stripped it and cleaned the metal with some No. 9 and steel wool which had a wonderful result. Having no wood repairing skill i asked dad about the stock who was equally stumped. I then concluded to get a replacement stock online. I did my research and saw that there were early and late war rifles and upon picture comparison i saw that i had a early war. This stumped me because the markings made it seem as if i had a late war rifle. I ordered an early war stock from Liberty Tree Collectors and waited.

I recieved my stock today and when i unpackaged it and put it next to my old stock i was stumped. The new stock was about 5 inches shorter than the original. I didnt see any info about any other models of type 99. I dug a little deeper online and saw that i had a type 99 long rifle. More collectable and rare than other standard models with only around 38,000 being produced. Meaning very very few parts floating around.

I restore old rifles to breathe life into old beauties and get them back into working order so than can do what they were meant to do. I want to get those old woman back in the field but i want that stock repaired first. Is it possible to clean up this stock any or is it a lost cause? Like i said, i have no wood experience so i will take any ideas.

Trying to upload pics, they keep failing...

Last edited by UserOfMosins; April 13, 2018 at 12:22 AM.
UserOfMosins is offline  
Old April 13, 2018, 12:02 AM   #2
Senior Member
Join Date: November 29, 2007
Location: Everett, WA
Posts: 6,080
Old wood can be restored to a degree. dents can be steamed out to a certain extend. warps can be straitened out. All that requires is steam and a jig to hold the wood in place as it drys out.
Cracks are more problematic. If the old glue job is bad you need to get that old glue out and start over. Cracks that affect the integrity of the stock are going to need "mechanical" reinforcement.
Dents. You might want to move the iron around more than this guy does.

Straightening bent wood is similar to getting out dents, but with more steam and water.
The hard part is setting up clamps or a jig to bend your stock into the right shape. the steam is made in a steam box or even a large plastic bag, depending on the size of the wood.

Good luck.
Buzzcook is offline  
Old April 13, 2018, 02:00 AM   #3
Senior Member
Join Date: October 19, 2005
Location: Tx Panhandle Territory
Posts: 3,679 You might give these folks a holler. I didn't see anything for the "Long Rifle Type99", but they might surprise you with what they don't have listed.
Rednecks... Keeping the woods critter-free since March 2, 1836. (TX Independence Day)

I'm going to use the words "clip" and "Long Colt" every chance I get. It grinds my gears to see new members attacked when we all know dang good and well what's being refered to.
10-96 is offline  
Old April 13, 2018, 01:02 PM   #4
T. O'Heir
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 9,665
"...The new stock was about 5 inches shorter..." A very wild guess says they sent you a Type 99 short rifle stock. Gunparts indicates there was a Short and Long Type 99.
" about any other models of Type 99..." Go here. Huge, well researched site, about most stuff Japanese arms. Go to the Nambu World main page linked at the bottom too. The Advanced Research Corner page as well.
Spelling and grammar count!
T. O'Heir is offline  
Old April 14, 2018, 08:58 AM   #5
Junior Member
Join Date: November 27, 2014
Location: Georgia
Posts: 7
I appreciate all the help, after i get off this 4 day stretch i will fiddle with the rifle a little more!
UserOfMosins is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 10:09 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.04552 seconds with 10 queries