The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools Search this Thread
Old December 1, 2020, 12:52 PM   #1
BJung
Senior Member
 
Join Date: December 5, 2019
Posts: 748
Neck expansion question

I have a question to ask about proper neck expansion for cast bullets.

My rifle slugs at .3105" so the proper sized bullet should be .3125". If I hone out my bullet sizer to .3125, using the current expander of .3110" leaves a difference of .0015". What is the ideal difference between the resized cast bullet and the inside diameter of the resized neck of optimal accuracy? I don't think I can get away with the current .311 expander. A bullet sized at .311" using the Lee sizer die kit fits just right.
BJung is offline  
Old December 1, 2020, 01:25 PM   #2
USSR
Senior Member
 
Join Date: November 14, 2017
Location: Finger Lakes Region of NY
Posts: 1,216
burbank_jung,

A couple questions. First, I am not familiar with the Lee bullet sizer, but is it made of soft enough steel so as to be honed out? Second, I don't know what rifle you are talking about, but anywhere's from .001" to .002" is enough case neck tension unless you are using a rifle with a tube magazine. And lastly, just because you have a .311" expander does not mean that the case neck inside diameter will be .311". Actually, it will be slightly less due to brass spring back.

Don
__________________
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
USSR is offline  
Old December 1, 2020, 09:42 PM   #3
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,135
Quote:
I am not familiar with the Lee bullet sizer, but is it made of soft enough steel so as to be honed out?
Sizing dies are hardened. They can be honed larger because the grit in the honing material is harder than the hardened steel.
I machined a sizing die one time when I was under the impression that soft mild steel being harder than cast bullets, it would not need to be hardened. I was wrong and after a short time of using it to size .430 cast bullets, the bore of the die had become much larger than original. After that, I remade the .430 die using W-1 drill rod and hardened it after reaming the bore of the die. Using hardened W-1 did the trick...the die maintained its inside diameter for the many years I used it.
dahermit is offline  
Old December 1, 2020, 10:14 PM   #4
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 18,270
BartB says the military armorers found 0.0015" to maximize accuracy with jacketed bullets in their 30 cal guns. Cast bullets typically get about 0.001" more because they are usually that much wider than jacketed bullets, but that doesn't mean they wouldn't like 0.0015" better. Unfortunately, this can be dependent on the gun and the load, so you are going to want to try it and see.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old December 1, 2020, 10:45 PM   #5
BJung
Senior Member
 
Join Date: December 5, 2019
Posts: 748
Uncle Nick, thanks for answering another question I had for jacketed bullets. I was thinking of expanding case necks before seating 174gr FMJBT bullets before seating them. The only question is if I should anneal the necks and graphite the necks too.

I measured the RCBS expander plug diameter as .3105" compared the sized bullet through a Lee bullet sizing die as .31105" That's a difference of .001"

I have to correct an earlier typo. The slug I pushed through my T99 Arisaka was .31105". The bullet diameter should be +.001 or .31205". The inside diameter of the case neck goes back -.001 and I'm back to .31105" or an additional -.001 according to Uncle Nick which is .3105", which the current plug measures at. Using the jacketed variance might be better to avoid swaging, plus I'm using gas checks.. Hmm.. okay, thanks for letting me think this out.
BJung is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2020 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04892 seconds with 10 queries