The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old January 22, 2020, 03:48 PM   #1
dyl
Senior Member
 
Join Date: October 31, 2009
Location: Ohio
Posts: 1,069
Old H&R Top Break

I'm trying to figure out if this old revolver is chambered in 32 S&W (which it says it is) or 32 S&W Long which according to my google-fu it is. I'd just like any people in the know to comment.

It says
May14, August 6 '89, April 2 '95, April 7 '97
Auto Ejecting 32 S&W CRTG

And it has 6 charging holes in the cylinder, target emblem grips that have a back strap that step down to fit the body of the grips.
https://imgur.com/IREodFv
https://imgur.com/9KUCRrq
https://imgur.com/mOUTXIN

And would it work if I just bought 32 S&W Short rather than Long for reduced pressures?

Last edited by dyl; January 23, 2020 at 09:46 PM.
dyl is offline  
Old January 23, 2020, 07:00 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 13,900
Since it says 32 S&W, use 32 S&W in it. Always use the cartridge the firearm is marked for.

And just food for thought, there is no 32 S&W Short, just 32 S&W and 32 S&W Long. What you are calling 32 S&W Short is 32 S&W.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old January 23, 2020, 11:20 PM   #3
dyl
Senior Member
 
Join Date: October 31, 2009
Location: Ohio
Posts: 1,069
So there is no 32 S&W short! Ah hah! From my internet reading I was under the impression that these H&R top breaks were either S&W Short or Long, which didn’t fit what was stamped on the barrel. I thought that maybe nomenclature became more specific since then. This makes it much easier and I would feel much better shooting what’s actually on the barrel.
dyl is offline  
Old January 24, 2020, 12:15 PM   #4
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 15,972
As Scorch says, there is .32 S&W which came out in the 1870s for topbreak revolvers and the .32 S&W Long which came out with the Hand Ejector (swing out) guns around 1896. So for about 20 years, there was only the one .32 S&W, no need for short or long like the other guys, and they did not see the need to rename the .32 S&W when the .32 S&W Long came out.

There were also .32 H&R and .32 MH. The .32 H&R will accept .32 S&W Long.
The .32 MH is very similar but of a particular OAL because of the Merwin & Hulbert revolver's peculiar "selective extraction."
Jim Watson is offline  
Old January 24, 2020, 01:53 PM   #5
stinkeypete
Senior Member
 
Join Date: July 22, 2010
Location: Madison, Wisconsin
Posts: 383
I have a real fondness for old Harrington and Richardson top break revolvers as my first pistol was a “.22 Special”... a long barrel top break target pistol the Pennsylvania Highway Patrol bought to save money on practice ammunition. That’s what Cooper the Trooper told my dad when he sold it to him in the early 1950’s.

Keep in mind they are not sturdy or built to shoot lots and lots...
stinkeypete is offline  
Old February 5, 2020, 11:56 PM   #6
dyl
Senior Member
 
Join Date: October 31, 2009
Location: Ohio
Posts: 1,069
I hear you stinkeypete, I might just buy a small quantity of ammo shoot it rarely. The opening action is very fun. I could do that all day (but would probably wear it out)
dyl is offline  
Old February 9, 2020, 04:30 AM   #7
TruthTellers
Senior Member
 
Join Date: October 22, 2016
Posts: 3,036
I'm gonna start doing a copy/past job for people asking questions on their .32 S&W top breaks because this question comes up at least twice a month.

From what I can figure, if your H&R has the cartridge marked on the side of the barrel, it's meant for smokeless powder. In addition to that, if it is also a 6 shot and not a 5 shot, it's meant for .32 S&W Long.

If your H&R top break can chamber .32 S&W Long, then it is meant for .32 S&W Long.

I cannot understand why H&R would make a cylinder that is capable of chambering .32 S&W Long yet intended it to be used only with .32 S&W. That's a lot of unnecessary steel and bullet jump for no reason.
__________________
Any good revolver > Any good semi auto

"We always think there's gonna be more time... then it runs out."
TruthTellers is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08284 seconds with 9 queries