July 13, 2018, 03:53 PM | #1 |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
308 Bullpup War....
As far as I can tell, there are three manufacturers of modern 308 Bullpups which can be purchased by civillians: Kel-Tec RFB; Desert Tech MDR and K&M M17s. I have included photos of each below. The Kel Tec is by far the least expensive and can be had for around $1,400. The DT MDR runs about $2,500 and the K&M M17s runs $2,000.
The Kel-Tec was just too much plastic for me - I would never be satisfied with it, knowing that the other two 308 bullpups were out there. So, after comparing the K&M and the DT MDR, I went with the K&M. Here's why: M17s was made of high quality aluminum, upper receiver and lower receiver - no plastic; Size was just a tad longer than the MDR, but more compact than the Kel Tec. The trigger is basically a fully adjustable AR competition trigger - really a nice touch All three are gas adjustable, so that was not a factor The deciding factor, however, was the bolt and bolt carrier assembly. By far, the M17s was the most robust of all three. In fact, the bolt on the MDR looked fragile in comparison. The MDR bolt looks like something the Swiss would over-engineer, and I really like that! Plus, the bolt uses extractors and extractor springs which are commonly found, so spare parts won't be a problem. Not to mention, it was $500 cheaper than the MDR. Granted, the MDR is probably the sexiest looking of all three. But, I was going for heavy-duty over sexy. My M17s is on order and I've been told that it will be delivered before the end of July 2018. I can't wait! 1. Kel-Tec RFB 2. Desert Tech MDR 3. K&M M17s Last edited by Skans; July 13, 2018 at 04:15 PM. |
July 13, 2018, 04:58 PM | #2 |
Senior Member
Join Date: April 16, 2017
Posts: 323
|
What about the Tavor 7? $2099 MSRP
|
July 13, 2018, 05:34 PM | #3 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
The Tavor will be an interesting option, once it hits the States.
I picked up an unfired second hand M17s a month or so ago, very nice and simple rifle. My initial range trip with my improvised rest, so so shooting skills, cheap ammo, and scope(not the one pictured) that I have difficulty sighting with, I wasn't thrilled with the accuracy. I intend to head to the range with a wider variety of ammo this week to see if I can find something the rifle likes. The pictures aren't the best, but better than nothing? |
July 14, 2018, 10:35 AM | #4 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
I've been waiting to see if the Tavor 308 would ever hit the US market. So far as I can tell, it's been promised for a couple of years now, but nowhere to be found. I gave up waiting
Quote:
How does it feel, weight-wise? Is the trigger as good as other's have described? Reliability? |
|
July 14, 2018, 11:25 AM | #5 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
The trigger has some takeup, but a solid wall, and very light break, the trigger feels really good.
It is a bit hefty, the pictured setup is around 10 lbs unloaded, I don't have a very good scale for measuring though, and that scope and mount is fairly hefty. Being a bullpup, the weight does carry quite well. I've only had somewhere around 60 or 80 rounds through it so far, I've had a few malfunctions while messing around with the gas regulator, but I think I have it set in a good position now. As far as accuracy comparisons, my experience in .308s is with an 18" PTR91, 12.8" G3K "clone", and a pair of Hk SL7s. I can get around 2" groups with the SL7s pretty easy with the cheapest brass case ammo I can find, the PTR91 was probably double that with the same ammo, and the last "pattern" I shot with the G3K was around 7", I really need to try some different ammo with that one too. I'm no target shooter, I collect stuff that interest me, and don't actually get out to the range as much as I want or should. I typically just use a blanket wadded up in my range bag as a rest, and fire the cheapest brass case ammo I can find. I believe the M17s is plenty more accurate than I've experienced so far, I just need to spend a little more time with it. I'll be looking forward to hearing how your like yours here shortly. |
July 16, 2018, 08:54 AM | #6 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
I looked at the MDR's bolt and, without an abundance of cheap replacement parts, I wasn't convinced that it would withstand abuse. When I buy an expensive gun from a start-up company, I want to make sure that it is robust and serviceable. Because, we all know that either of these companies might not be here 5 or 10 years from now. |
|
July 16, 2018, 10:10 AM | #7 |
Senior Member
Join Date: March 16, 2011
Posts: 489
|
I agree, I think the Tavor 7 will be winning this field. They have built a strong positive reputation for their 5.56 bullpups. Another winning point is their price point will probably beat the others too.
That being said, that Desert Tech looks amazing. I would get that one over the Tavor if it weren't for that price tag. |
July 16, 2018, 10:42 AM | #8 |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Here's a comparison of the Desert Tech MDR's internals and the K&N M17s. I'm not all that impressed with the DT's bolt and bolt carrier compared to the M17s
The First photo shows the MDR bolt. The second, the M17s Bolt, and the 3rd compares the M17s Bolt to an AR bolt. |
July 17, 2018, 06:29 AM | #9 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
What does that little buzzard do to your hearing if you actually fire it w/o ear protection?
|
July 17, 2018, 07:54 AM | #10 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
I don't intend to find out, I typically double up on hearing protection on anything bigger than .22LR anyway, so the shorty 308's don't bother me.
|
July 19, 2018, 02:53 PM | #11 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
Well I got back out to the range with a variety of cheaper ammo, and some Federal Gold Medal Match 168 gr. Of course I forgot to bring a tape, or scale, and I was using adhesive targets, so I'm guestimating the group/pattern size off of the ammo boxes.
The first couple of pictures are of my super precision shooting rest, spotting scope, and rifle. The three pictures with the FGMM were all somewhere around 3 3/8" or perhaps an insignificant greater or smaller. The cheap Monarch ammo patterned quite impressively. The target with just a casing on it was using Aguila 7.62X51. All of the less spendy .308 I've tried(Winchester 147 gr, Aguila 150 gr, MEN 147 gr, Monarch 150 gr, Federal XM80 149 gr) patterns similar to the last two pictures. The rifle shoots good enough with match ammo to satisfy me, but if I can't find something for less than $26 a box with similar results, I'm not going to be doing a lot of shooting with this rifle. |
July 19, 2018, 02:55 PM | #12 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
The rest of the FGMM, and the Monarch.
|
July 19, 2018, 02:57 PM | #13 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
And the Aguila. I didn't bother trying to measure the Monarch or Aguila targets.
The rifle had one failure to eject with the Monarch ammo, but otherwise functioned just fine. |
July 20, 2018, 11:03 AM | #14 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
1. What distance were you shooting from? 2. How was the recoil and noise? How comfortable was it to shoot the M17s? 3. Did you attempt to see how fast you could shoot 2 or 3 shots? 4. Did you feel that you were getting full power and velosity from the ammo you were using; i.e. was there a ton of muzzle flash and unburned powder. 5. Would it be possible to comfortably use 30 round magazines? |
|
July 20, 2018, 12:31 PM | #15 |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
1. Whoops, thats a glaring omission! 100 yards.
2. Recoil is ok, probably a bit more than an M1A, but less than an Hk RDB design. You know you're shooting a .308, but I don't consider it bad. I wear 30 NRR muffs over earplugs, and the noise doesn't bother me. Wearing only plugs, or muffs is louder than I'd like. That being said, during my baseline hearing test, the tech commented on how sensitive my hearing was, and my co-workers regularly make fun of me for wearing plugs when they don't feel the need to. 3. I didn't try any fast followup shots, I was primarily concerned with whether or not the rifle would "group" rather than "pattern" this last trip. 4. Beats me, I didn't notice any muzzle flash, but I wasn't looking for it either. 5. From a bench? No. I didn't realize there were 30 rounds magazines out there, I do have a couple of 25 round mags, and they work fine in prone position, but there isn't a whole lot of room to spare, prone would likely be an iffy proposition with a 30 round magazine. |
August 29, 2018, 11:57 AM | #16 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
The only plastic on this rifle is the AR-style pistol grip. This 308 Bullpup is nearly the identical length of my 13" barrel AC556 while folded. The 308 however has a 16" barrel. I am amazed at how compact this rifle is especially for a 308. The bolt-carrier/bolt carrier unit looks indestructible, and it is fairly easy to service if needed. The gun is comfortable to shoulder, but you'd swear it's an SBR when shouldered. The mag release can be operated from the right or left side, which is nice. Fit and finish is excellent. The trigger has a tiny bit of take-up. Apparently the trigger is adjustable, so I will need to play with this and see if I can eliminate the take-up. Other than that, the break is clean and crisp. I'm looking forward to shooting it to see how it is to handle and shoot. |
|
August 30, 2018, 07:33 AM | #17 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
$2000-2500 for a rifle with no practical purpose since it's unbearable to shoot w/o a face shield and doubled ear protection???
|
August 30, 2018, 07:50 AM | #18 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
|
|
August 30, 2018, 12:25 PM | #19 |
Senior Member
Join Date: March 15, 2010
Posts: 8,238
|
I like the concept, but I can’t put my face any closer to the explody part than a traditional rifle.
|
August 30, 2018, 12:52 PM | #20 | |
Junior member
Join Date: July 26, 2001
Location: midwest
Posts: 2,374
|
Quote:
Although the engineering purpose of the Tavor/Bullpup-type designs may be to gain a more 'compact' weapon, the set up isn't at all practical other than as a Sunday afternoon range toy - unless it's run suppressed. Suppression (with a good can) eliminates the up-close concussive blast and auditory damage, especially if fired in rapid sequences, like double/triples taps. Once you've suppressed away those issues, and if you can get used to the bullpup's different mechanics of reloading and manual-of-arms (versus the M-4/AR-15 school), then you might have something interesting. |
|
August 30, 2018, 02:01 PM | #21 | |
Senior Member
Join Date: January 4, 2013
Posts: 888
|
Not a whole lot impractical about the bullpup design, there are some obvious tradoffs as opposed to conventional designs, but its mainly just misconceptions and people parroting what others have said rather than real experience to back their objections to bullpups.
The fact that several militaries around the world have been using bullpups as front line rifles since the 70's should point to the practicality of the design. By all means I understand a bit of hesitancy when someone is first introduced to the concept, but I honestly find most arguments against bullpups absurd. Quote:
Have you ever held or fired a bullpup? You're quite obviously free to your opinion either way, but I would be interested to know if this is based on experience, or simply conjecture. |
|
August 30, 2018, 05:08 PM | #22 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
I noticed that the serial number on my K&M was in the 250's. At $2K, I doubt they are even making a profit yet, especially given the exceptional quality of each component of this rifle. As far as "churning them out" - I can assure you, that they aren't. I had to wait 4 months to take delivery of mine. The anodizing alone was taking 2 weeks, since each piece needed to be separately anodized and coated. Even Keltec charges over $1,500 for it's RFB, and the chassis is screw-together plastic panels. I think if you check around, you'd see that $2K for a good quality 308 Bullpup with an adjustable trigger, adjustable gas valve, professional quality all metal construction, with the high-quality bolt and bolt carrier assembly is actually a pretty good deal. Now, if you just don't like bullpup 308's, I get it. Pay $1,500 more and get the SCAR. |
|
August 30, 2018, 07:22 PM | #23 |
Senior Member
Join Date: April 16, 2017
Posts: 323
|
I like the bullpup design. In particular I like the old school design of the AUG.
Most of the firearms we own are manufactured for specific purposes. My O\U 20 gauge has limited but specific scope of use, as does say a Ruger Mark III or chassis built bolt gun chambered in a long range caliber. Or perhaps a super light weight mountain gun and save room for a AR, AK, and a High capacity 9mm like a MPX "pistol". I could go on for days. Lot's of flavors to savor. |
|
|