January 2, 2021, 06:53 PM | #26 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
No, it's not inaccurate.
The patterns you see in laminated steel are exactly where the steel is not homogenous. Break a piece of your "damascus" and see if it does not separate in the laminations. Because you make pattern welded steel for knife blades does not make you an expert, nor does it make your dangerous statements legitimate. Pattern welded steel is not as strong as a homogenous steel. If it were, there would be no pattern. It is better to not shoot old laminated steel barrels. They could blow up- this is not a guess, it actually does happen. Is this a blanket statement? You're darn right it is, because it's better to be safe than sorry. |
January 2, 2021, 08:30 PM | #27 | ||
Senior Member
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
|
Quote:
Quote:
__________________
Never try to educate someone who resists knowledge at all costs. But what do I know? Summit Arms Services |
||
January 2, 2021, 09:36 PM | #28 | |
Senior Member
Join Date: October 25, 2001
Location: Alabama
Posts: 18,541
|
Quote:
Chemistry class assumes charcoal is carbon so as to simplify the equations. It really isn't but still about 70% fixed carbon, balance partly decomposed cellulose and lignin which do affect performance. So there can't be a lot of sulfuric (more likely sulfurous) acid. And there is a lot of potassium carbonate, an alkali which will neutralize acids. Leaving salts, which are somewhat corrosive but not in the class of the potassium chloride from chlorate primers. |
|
January 4, 2021, 09:45 AM | #29 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
All I know is I'm still shooting the same Bill Large rifle and pistol barrels today 40 to 50 years after I built the guns and they're still as accurate as the day they were built. Rifling still sharp. If metal were removed then they would have lost their accuracy. At least you're admitting you don't know how much the barrels were weakened.
Bill, no the patterns you see are the two different types of steel - low carbon and a higher carbon steel. The same as when I use 5160 and 01 for my Damascus knives. Two different steels. I'm not saying Damascus barrels are as strong as homogenous steel. But they have been tested with proof loads, and more than proof loads, and have been found safe. Some of you guys go on and on about how Damascus barrels aren't safe to shoot, but everyone of you ignore me when I ask why the Brits still, and always have, proofed Damascus barrels, and if they pass proof they're deemed safe to shot. Someone please answer that. Last edited by bladesmith 1; January 7, 2021 at 09:57 AM. |
January 4, 2021, 10:44 AM | #30 |
Senior Member
Join Date: November 11, 2006
Posts: 2,519
|
Have Granddad'Remiington1894 SxS. About 2011/ 2012 did research on the known information.
Obtained a copy of the Remington Salesman handbook, where is stated that the Damascus barrels of the 1894 & 1900 models, were "Proofed" by Remington with the CURRENT nitro-powder proof-loads at that time. The main problem was chambers were for the 2-1/2"chambers, as informed by the source, compounded by poor maintenance. Last year I was at a recognized Master Gunsmith of the Westside of the state, he had a number of the Remingtons on rack and he inspects and cleared those as ready for use. Some the chambers were lengthen other using 2-1/2 shell. [he specified a particular shell manufacture to use. Once the COVID dies off, I am having the SxS examined and possibly cleared for use. My Dad last used the the 1894 in the early 70's using Remington GL high brass paper shells. In the Mid-80's, i bought the "Spot-Chek" kit for examing the barrel outside surface, clean and degreased with acetone , let dry and placed the barrels in a 200 degree kitchen oven, set for fifteen minutes, took outside and sprayed the penetrate let dry / cooled and wipe-off the surface ,, then applied the developer. No red spot show-up. This was done for when cleaning the fore-arm was removed and the Damascus pattern faded away?? Last year I purchased a$24 mini-camera with 36-inch lens lead and slowly examined the bore, nice an shiny. Once the smith examines and cleans/lubricate the boxlock action, then I will decide to use it. My $0.02 worth. |
January 4, 2021, 11:54 AM | #31 |
Senior Member
Join Date: July 22, 2010
Location: Madison, Wisconsin
Posts: 1,293
|
There are shotgunning enthusiasts who collect and fire superior quality double barrel shotguns from the last century, picking up rich man’s toys from the past century at bargain basement prices.
These fellas know intimate details about their fine old firearms. They shoot very low pressure shells. They enjoy their hobby and you can find lots of scholarly works they publish online. They put far more work in to it than I care to, and I like goofy stuff like this! If you have to ask, it’s not safe for you.
__________________
My book "The Pheasant Hunter's Action Adventure Cookbook" is now on Amazon. Tall tales, hunting tips, butchering from bird to the freezer, and recipes. |
January 4, 2021, 02:47 PM | #32 | |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,833
|
Quote:
As I see it, what we are discussing here (or arguing over?) is that statements made are taken to extremes, including when the statement was not meant to be. We're making statements with verifiable proof, on both sides, and they are being taken as if they apply 100% to ALL guns. They don't. The only one that does apply is that when there are unknowns, there is an element of risk. Some Damascus guns have failed. Fact. Some Damascus guns have been tested and did not fail. Fact. ALL Damascus guns will fail. NOT FACT. ALL Damascus guns will not fail. NOT FACT. Proof testing is a fine thing. It proves that gun survived X amount of overpressure above standards operating pressure. ONCE. I once "proof tested" a Mustang by "burying the speedometer". Does that mean every Ford will do that? No. THAT one did. Machts Nichts. Damascus is a general term, in the sense that it refers to the style of manufacture of the barrels, and does not specify the precise materials used or the quality of manufacture. And, it tells us nothing about what the barrels have endured in the (general) hundred years plus, since leaving the factory. All we have is what we can see, and whatever "story" came with the gun, if any.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
|
January 4, 2021, 03:07 PM | #33 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
50 years ago there wasn't very many people even making pattern welded steel, and you did? I know just a little bit about it.
Regardless, we are discussing old damascus guns and the damage time has done, not new custom made ones. |
January 4, 2021, 06:15 PM | #34 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
In the 90s I went to the ABS school, first for forging knives, then a class for making Damascus. Came home and built a forge. Also bought a power hammer, a 35 pounder to be exact. A year or two latter I went to Ron Claybournes place in Tenn. for a hammer in. There I bought one of his 25 ton knife making presses. Returned when it was done and spent a week with him learning all about " my new press". I made up some dies for different patterns and also learned about using high carbon powdered steel in tubes for just pressing Damascus out with one or two heats. There are a good number of guys who have learned how to make Damascus steel.
I'm sorry if I came off sounding like ALL Damascus guns are safe to shoot. But at the same time some of you are claiming Damascus barrels had voids and rusting from the inside out, cracks on the surface that allowed sulfuric acid to get in them, and so on is all incorrect. I belong to the National Muzzle Loading Rifle Assoc. and in 50 years have never seen a statement about sulfuric acid forming from BP residue and weakening the barrels. Never once. Glad to see someone gave a intelligent answer to my question about the British proofing Damascus guns. You explained it all. And Sherman Bell proof tested 20 DAMASCUS BARRELED WALLHANGERS. Not well taken care of guns, but ones that were totally abused, and all came through with flying colors. I'm not sure what you want. |
January 5, 2021, 12:40 AM | #35 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
50 years ago was the early 1970s.
|
January 7, 2021, 09:53 AM | #36 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
sorry, repeat post i tried deleting
Last edited by bladesmith 1; January 7, 2021 at 10:25 AM. Reason: repeat post |
January 7, 2021, 10:23 AM | #37 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
jrothWA, the Remington shotguns had 2 9/16" chambers to be exact. I have a 73, 82, 89, and six 1894 Remington shotguns. All have Damascus barrels except three of the 94s, which are F grade trap guns. I shoot 2 3/4" shells in all without a second thought. My reloads are 7/8 or 3/4oz out of respect for the 100+ year old wood. They all have a lot of DAH so those light loads are also for respect for my cheek and nose.
|
January 7, 2021, 10:32 PM | #38 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
First you tell us damascus barrels are safe to shoot.
Now, you're telling us it's safe to shoot long shells in short chambers? Wow. |
January 8, 2021, 01:01 AM | #39 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,189
|
I did that a lot when I was a kid and didn't know any better. I wont do it now and once I accidently fired a 3 inch magnum out of my 1887 Winchester. I thought it blew up at first but other than the case head separating no damage was done.
|
January 9, 2021, 11:49 AM | #40 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
Bill, you just need to get out a bit more. I'm kind a curious. How does one earn the title " Master Cutler " ? In the ABS they have " Journeyman " and " Master " class and there are certain qualifications to be a member of the Knifemakers Guild, but I had never heard the term " Master Culter " used before. Who issues that title ?
No, Damascus barrels are not as strong as new fluid steel barrels. Does that satisfy you guys ? But they are plenty strong enough to fire shotgun shells in. And yes, Sherman Bell shot 3 1/2" 10ga proof loads in old Parker Damascus barreled shotguns with 2 7/8" chambers with no ill effect. He also shot 2 3/4" shells in Damascus barreled guns with 2 1/2" chambers, with no ill effect. Pressures went up from 500psi to 1000psi. Sorry, nothing blew up. |
January 9, 2021, 02:20 PM | #41 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
Since we're getting personal-
I have been making, repairing, designing, restoring and embellishing knives for around 50 years. I'm a trained jeweler, and an engraver-among other things. I have knives actually in production. I'm an authorized repairman for Flylock, Press Button, Presto, Schrade, Colonial, Hubertus, Kuno Ritter, Latama, Mauro Mario, Falcon/AKC/AGA Campolin, KaBar, and Lepre Cutlery. As a rule, I don't forge knives, but I'm pretty well-versed in most areas of knife making. I also held an FFL for many years and did custom gunsmithing. Still make some parts and do some engraving-just not on firearms frames. I issued my own title. Do you wish to dispute it? I do a little more than just make knives. Have a look at my web site. Last edited by Bill DeShivs; January 10, 2021 at 02:30 PM. |
January 10, 2021, 07:47 PM | #42 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
Hello?
|
January 11, 2021, 09:15 AM | #43 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
Sorry I didn't get right back. I keep busy running the shotgun venue three times a week at the club I belong to. You listed quite a resume. I'm sorry that I questioned where your self imposed title came from. Now I know. Maybe I'll start calling myself " God of Damascus ".
|
January 11, 2021, 04:43 PM | #44 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
Perhaps you could call yourself "stubborn."
When you call yourself "God of damascus," you'd better be able to back it up. Neophytes will question you. Last edited by Bill DeShivs; January 11, 2021 at 08:57 PM. |
January 14, 2021, 03:47 PM | #45 |
Senior Member
Join Date: July 14, 2018
Posts: 240
|
stubborn - pot calling the pan black.
|
|
|