April 15, 2008, 06:54 PM | #1 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
Birdshot loads
I am looking to work on birdshot loads for my ROA BP. Anyone have any advise on a shot cover that would hold under recoil?Material,....thickness..etc...
|
April 15, 2008, 07:10 PM | #2 |
Senior Member
Join Date: March 4, 2008
Location: west virginia born 1/19/1961
Posts: 222
|
might take time to dry, what about clear silicon chaulk? put drop on top level it off and push in with finger.
|
April 15, 2008, 07:29 PM | #3 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
Birdshot
That sounds like a good idea. Wonder what ignition temp would do to it?
|
April 15, 2008, 07:36 PM | #4 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,189
|
Birdshot out of a rifled barrel isn't going to work well. A thin piece of cardboard glued in with Elmers glue would work tho. Elmers will dry faster than caulk. An over powder wad would probably work but I have no idea what it will do to your pattern, not that you're going to have much of a pattern anyway.
|
April 15, 2008, 07:42 PM | #5 |
Senior Member
Join Date: March 4, 2008
Location: west virginia born 1/19/1961
Posts: 222
|
never thought about that, might get a bit gooey.
|
April 15, 2008, 07:54 PM | #6 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
Birdshot
I have used the CCI 357 shot loads on barn birds {pigon} up to 30 ft in a 6" bbl 686 S&W and had alot of fun doing it. I figured there ought to be a way to load shot loads in BP revolvers. The elmers sounds like it would be less likely to leave anything in the bore.
|
April 15, 2008, 08:06 PM | #7 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,189
|
Yeah but those loads have the shot encased in a plastic bullet that helps negate the effect of rifling. What you're going to get is a big donut shaped pattern with a big hole in the middle.
|
April 15, 2008, 08:26 PM | #8 | |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
This was previously posted on another site:
Quote:
|
|
April 15, 2008, 08:30 PM | #9 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
So you would have to do a little KY windage to compensate for the center void. Sounds like a challange to come up with something to shrink this. I have read about guys loading shotshells for there centerfire revolvers using heavy cardboard crimped over #9 shot with good results at close range for snakes. Never have tried it though.
|
April 15, 2008, 08:41 PM | #10 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
Thanks arcticap........Do you know if they are sold in different diameters and thicknesses? I use a veg fiber wad .462 in dia. .030 thick. The diameter seems to hold well by pushing up on the cylinder wall. I would think this would work well as an over powder wad, but would be lacking in holding the shot chg under recoil......
|
April 16, 2008, 10:04 AM | #11 |
Senior Member
Join Date: April 14, 2008
Location: Stuart, VA
Posts: 2,473
|
Just leave enough room to seat a lead ball over the shot (and lube over the ball). Will hold in the shot and keep the rifling from spinning it too much. Just don't hit the bird with the lead ball if you can help it. This load would also be good for other critters in a pinch, but will not give you much distance with the shot.
|
April 16, 2008, 11:09 AM | #12 |
Senior Member
Join Date: February 6, 2006
Location: Hernando , Ms.
Posts: 579
|
You can use a 45 cal punch or an empty hull if it`s all you have ..I punch 45 cal wads out of foam picknic plates ..place 2 over the powder charge then one over the shot charge and glue in with white school glue .works good for snakes and small critters at 5 yards or so .
|
April 17, 2008, 12:21 AM | #13 | |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
Quote:
Here's an outfit that a lot of BP shooters buy sheets of felt from to make their own wool wads. You'll just need the right size punch. Note that at the top of the page, there's an item number for the dense felt material that BP shooter's usually prefer which is 1/8 inch thick "hard" felt. http://www.durofelt.com/image_26.html |
|
April 17, 2008, 04:55 AM | #14 |
Junior Member
Join Date: April 13, 2008
Posts: 14
|
Birdshot
Thanks for the info. What a great site! Can't wait to try some of the suggestions...
|
April 17, 2008, 06:07 AM | #15 |
Senior Member
Join Date: July 23, 2007
Location: Virginia
Posts: 719
|
Some times I'll load my Pietta 1858 with a shot load that consist:
15gr. FFFG over powder wad using the 15gr. measure, measure out #7 or #9 shot over shot wad a little wax over that to keep it all in place. With this load in a .44 caliber revolver you can use regular store bought wads or make your own & it is effective on snakes & rodents out to 7 yards maybe 10 but that'd be pushing it.. |
April 17, 2008, 09:26 AM | #16 |
Senior Member
Join Date: October 7, 2007
Location: New Hampshire
Posts: 215
|
Like others said, a wax wad over the shot will hold tit all in. Squish the wax in so it sticks to the cylinders walls good.
I had an idea for shot quick loads once but never tried it. I though of melting beeswax and mixing in lead shot then forming the proper sized cylindrical loads of it. Once cooled, you could put them in by hand and it'd be a self contained shot/wax load. |
|
|