The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old January 16, 1999, 01:24 AM   #1
swehrman
Member
 
Join Date: October 10, 1998
Location: Kalispell, MT. USA
Posts: 26
How many of you trim your pistol brass? More specifically pistol brass that headspaces on the case mouth. My thinking is that people who shoot semi-auto pistols and have progressive presses don't spend too much time trimming brass. I'm just curious.
swehrman is offline  
Old January 16, 1999, 10:23 PM   #2
dundee
Senior Member
 
Join Date: December 6, 1998
Location: mytown,mi,usa
Posts: 162
loading 9mm, 45, 40 cases I have never trimmed the cases. At my gun club I have never heard of anyone trimming this type pistol brass. In loading for revolver I occasionally trim the brass to get better roll crimps.
dundee is offline  
Old January 17, 1999, 01:06 AM   #3
Art Eatman
Staff in Memoriam
 
Join Date: November 13, 1998
Location: Terlingua, TX; Thomasville, GA
Posts: 24,798
You don't get the stretch in straight-wall cases that you get in bottle-necks.

My .45ACP stuff usually splits before any stretching could happen, anyway...
Art Eatman is offline  
Old January 17, 1999, 10:54 PM   #4
Michael Carlin
Senior Member
 
Join Date: October 13, 1998
Location: Fredericksburg, VA USA
Posts: 193
I have reloaded both rifle and pistol since 1967 and NEVER trimmed a straight wall pistol case. These cases tend to shorten up as they are worked rather than stretch.

I would have to say that my revolver reloading experience is no too extensive. Probably less than 10,000 rounds. So perhaps in revolvers......(but I think not!)

In locked breech autos, no need to trim brass, in my opinion.

------------------
Ni ellegimit carborundum esse!

Yours In Marksmanship
http://www.1bigred.com/distinguished

michael



[This message has been edited by Michael Carlin (edited 01-17-99).]
Michael Carlin is offline  
Old January 20, 1999, 02:52 PM   #5
leapfrog
Senior Member
 
Join Date: January 19, 1999
Location: Texas
Posts: 107
To quote a locally noted pistolsmith that built a 1911 for me. "Don't waste time trimming brass for accuracty sake. If you want ultimate accuracy with reloads, weigh the bullets, cases, and powder charges individually - then get them as close to the same as possible."
leapfrog is offline  
Old January 22, 1999, 12:43 PM   #6
Cheapo
Senior Member
 
Join Date: November 19, 1998
Posts: 986
For straight-wall autos, the time involved is most economically spent miking a sample of at least 30 resized cases to establish the range of lengths. Trim to max or midway between max and "trim-to" lengths, only those which are too long.

Betcha won't find any...

Then sort your brass into the shorter half, and the longer half. Longer brass tends to give slightly tighter groups, according to some sources. More consistent ignition from less flopping around under the firing pin strike or something like that. Use the long brass for your 50-plus yard work.

For revolvers, however, I trim after the first reload, then about every five thereafter. Do the same for bottleneck rifle I'm crimping into a channelure.

Enjoy!
Cheapo
Cheapo is offline  
Old January 22, 1999, 02:25 PM   #7
Steve Koski
Member
 
Join Date: October 19, 1998
Location: Spanish Fork UT, USA
Posts: 86
Never trimmed a pistol case.
Steve Koski is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06116 seconds with 8 queries