|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
December 21, 2019, 01:09 PM | #1 |
Member
Join Date: January 17, 2017
Posts: 85
|
Swedish Mauser oddball ID help
Hello everyone. I’ve acquired a new Swedish Mauser and can’t exactly tell what it is. The barrel is about 18 -19 inches. Has a bent bolt handle and a model 96 rear sight. It also has a marking under the receiver that reads BS. The front sight also has a peculiar band around it. Any help on the ID will be appreciated. I will post pics promptly
Here’s the website for pics https://imgur.com/a/adCSxk0 Last edited by Mattj4867; December 21, 2019 at 03:18 PM. |
December 21, 2019, 02:04 PM | #2 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
There was an M92 carbine, an M94 Carbine and an M38 Carbine. The M94 Carbine had an 18" barrel.
Then it gets weird as the Swedes made M94's for their civilian schools. All of which have receivers stamped with 1901. Then there was an M94 "gallery carbine". All serial numbers prefixed by K. A 1894/96 Fortress Carbine and M1894 carbines hand-built by weapons officers. This might be of more use to you. http://www.gotavapen.se/gota/mats/ma...user_rifle.htm
__________________
Spelling and grammar count! |
December 21, 2019, 07:52 PM | #3 |
Senior Member
Join Date: October 9, 2018
Posts: 217
|
You have the remains of a chopped up rifle .
|
December 22, 2019, 07:53 AM | #4 |
Senior Member
Join Date: February 7, 2008
Location: pa.
Posts: 2,450
|
winner,winner a chicken dinner. bubba or his elf,s were busy.
|
December 22, 2019, 10:31 PM | #5 |
Senior Member
Join Date: April 2, 2002
Location: Falcon Colorado
Posts: 256
|
It might be a good shooter though.
|
December 23, 2019, 12:15 AM | #6 |
Member
Join Date: August 19, 2019
Posts: 58
|
That was most likely an M94 carbine, though the front sight band doesn't tell me enough to be certain. Presumably imported after 1968 since it doesn't have the pressed in false muzzle that was required prior to the GCA.
I have one that was rather nicely done in a Bishop stock in the early 60s, drilled and tapped for a scope. I've put it in a Boyd's "At One" adjustable laminate stock. Looks a bit like the old biathlon rifles now. Loses about 150-200 fps off the 24" load data barrels but is excruciatingly accurate with virtually any 140grs bullet, with the Hornady 160 grs RN, and with Nosler 123 grs Match since adopting a Timney trigger. I am quite certain yours will be a shooter. Enjoy! |
December 24, 2019, 07:41 PM | #7 |
Senior Member
Join Date: October 9, 2018
Posts: 217
|
Since it has the rifle sight it was not a carbine . It is a chopped up rifle as stated .
|
December 25, 2019, 04:38 AM | #8 |
Senior Member
Join Date: July 10, 1999
Location: High Desert NV
Posts: 2,850
|
What does it say on the receiver ring?
|
January 2, 2020, 09:47 PM | #9 |
Member
Join Date: January 17, 2017
Posts: 85
|
Thanks all of your input, it is indeed a chopped rifle but shoots amazing getting a scout scope put on it and am going try it out soon
|
January 2, 2020, 09:52 PM | #10 |
Member
Join Date: January 17, 2017
Posts: 85
|
1903a3 newbie
Hi all, I just picked up a 1903a3 at a pawn shop for well less than <$400. It is a smith corona made in October of 1943 and surprisingly has a correct barrel on it. Upon initial inspection the gun is very clean and looks like fresh Arsenal rebuild with the green parkerization and everything. The only downsides are that it has a aftermarket stock (actually a very nice one), Remington bolt, and the magazine lets the bolt close on empty. I’ve tried emailing the CMP about what the correct stock should be for this rifle but I have yet to get a response. Does anyone know what type of stock would be correct?
|
|
|