How interchangeable are parts for Browning HP/FEG PJK 9mm?

Gwinnydapooh · October 16, 1999, 01:06 PM

Do all parts interchange? If not, what doesn't? Are they exactly the same externally at least? (IOW, if my fiancee handles a Browning and likes the grip, am I safe to get a Hungarian FEG?)
Thanks!

------------------
Don

"Its not criminals that go into schools and shoot children"
--Ann Pearston, British Gun Control apologist and moron

Dakotan · October 16, 1999, 09:48 PM

Hello! I have done extensive customizing on FEG Hi-Powers, and found that MOST parts are fully interchangeable with the Brownings, although virtually ANY aftermarket parts will require some degree of fitting. If a Browning fits your girlfriend's hand well, so will the FEG. External dimensions of the FEG match Browning's virtually identically. I own 2 of these clones; one is a full-house custom, and the other is a lightly massaged carry gun. Both Novak, and Cylinder & Slide extended safeties fit, but require a bit of finesse to install. I prefer the C&S safety. Hogue rubber finger-groove grips drop right on, but if you want wood grip panels, some brands may require fitting. My Navidrex Dymondwood grips certainly did. If possible, try them in the store before you buy. The .285 in. rear sight dovetail dimensions match Brownings (I installed a Mec-Gar adjustable rear sight on my custom). Federal Arms barrels (among other brands) will drop in, but require a ton of chamber work to function reliably, as the FEG chambers are a bit oversized. The FEG's factory barrel provides quite acceptable accuracy, anyway. I just wanted a ported barrel on the custom, and don't regret the time it took me to get it to work well. At 15 yards it shoots 1 hole groups on my lucky days

Internal parts look like they should interchange also, and I'm sure at some point I will install a C&S hammer/sear set. By the way, a trigger job for this gun is a MUST. My carry gun breaks cleanly at 4.5 pounds with the well-polished magazine disconnect safety in place. This clone is an excellent value, and quite reliable with all of the ammunition types I've tried (including hollow-point rounds); you won't regret your purchase. Good Luck & Take Care- Dakotan

hotshot · November 4, 2008, 04:07 PM

Dakotan, I Just Read Your Information On How Interchangeable The Parts For The Feg Pjk 9hp Are With Browning. I See You Have Customized Yours. I Am Looking For A Laser Grip To Install On My Feg, But Non Are Available. There Is A Laser Grip For The Browning Hi-power, Do You Think This Would Work?
Thanks

November 4, 2008, 04:07 PM	#3
hotshot Junior Member Join Date: November 4, 2008 Posts: 1	Feg Pjk 9hp Dakotan, I Just Read Your Information On How Interchangeable The Parts For The Feg Pjk 9hp Are With Browning. I See You Have Customized Yours. I Am Looking For A Laser Grip To Install On My Feg, But Non Are Available. There Is A Laser Grip For The Browning Hi-power, Do You Think This Would Work? Thanks

October 16, 1999, 01:06 PM	#1
Gwinnydapooh Retired Screen Name Join Date: November 17, 2000 Posts: 978	Do all parts interchange? If not, what doesn't? Are they exactly the same externally at least? (IOW, if my fiancee handles a Browning and likes the grip, am I safe to get a Hungarian FEG?) Thanks! ------------------ Don "Its not criminals that go into schools and shoot children" --Ann Pearston, British Gun Control apologist and moron

October 16, 1999, 09:48 PM	#2
Dakotan Senior Member Join Date: August 24, 1999 Posts: 174	Hello! I have done extensive customizing on FEG Hi-Powers, and found that MOST parts are fully interchangeable with the Brownings, although virtually ANY aftermarket parts will require some degree of fitting. If a Browning fits your girlfriend's hand well, so will the FEG. External dimensions of the FEG match Browning's virtually identically. I own 2 of these clones; one is a full-house custom, and the other is a lightly massaged carry gun. Both Novak, and Cylinder & Slide extended safeties fit, but require a bit of finesse to install. I prefer the C&S safety. Hogue rubber finger-groove grips drop right on, but if you want wood grip panels, some brands may require fitting. My Navidrex Dymondwood grips certainly did. If possible, try them in the store before you buy. The .285 in. rear sight dovetail dimensions match Brownings (I installed a Mec-Gar adjustable rear sight on my custom). Federal Arms barrels (among other brands) will drop in, but require a ton of chamber work to function reliably, as the FEG chambers are a bit oversized. The FEG's factory barrel provides quite acceptable accuracy, anyway. I just wanted a ported barrel on the custom, and don't regret the time it took me to get it to work well. At 15 yards it shoots 1 hole groups on my lucky days Internal parts look like they should interchange also, and I'm sure at some point I will install a C&S hammer/sear set. By the way, a trigger job for this gun is a MUST. My carry gun breaks cleanly at 4.5 pounds with the well-polished magazine disconnect safety in place. This clone is an excellent value, and quite reliable with all of the ammunition types I've tried (including hollow-point rounds); you won't regret your purchase. Good Luck & Take Care- Dakotan