|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
January 15, 2013, 11:52 AM | #1 |
Junior Member
Join Date: January 7, 2013
Posts: 4
|
Remington 597 - extra spacer left after reassembly
Hi all - first post here and I'm looking for some help.
While disassembling my 597 .22 LR for cleaning I mistakenly left the bolt open when taking the trigger assembly out of the body. After I fully pulled the trigger assembly out, the bolt snapped shut and the hold-open assembly popped off of the trigger assembly. No big deal I thought because it has come off while cleaning before and I've been able to get everything back together correctly in the past. This time, while picking up the hold-open pieces from the floor I also found another part. Pictures of the other part, which look to me like a spacer, are attached. I cleaned and reassembled the firearm but still had this spacer left over. I haven't fired the rifle since, but I am able to move the bolt smoothly and the hold-open still works. I looked at the parts diagram in my manual and online (http://www.schiessen-erzgebirge.de/B...mingtn_597.jpg) but still can't find where this spacer goes. I've watched dis/assembly videos on Youtube and searched online. I called Remington directly, explained the situation, and essentially they said I could buy a new trigger assembly from them or take the rifle to a gunsmith and hopefully the smith could figure it out. I installed a VQ hammer & extractor years ago but don't think they would have anything to do with this spacer. Anybody have thoughts as to what exactly this spacer is for and where it goes? Thank you in advance. |
January 15, 2013, 01:26 PM | #2 |
Senior Member
Join Date: December 11, 2009
Location: South Carolina
Posts: 360
|
If my son didn't have mine I would pull it apart to see if I could help.Maybe hell come home soon so I can see.Sorry for now
__________________
life is great but its better when you can own as many guns you wish to own.for me I haven't bought enough yet. |
January 15, 2013, 05:39 PM | #3 |
Senior Member
Join Date: December 21, 2008
Location: Lower Alabama
Posts: 727
|
go to "rimfirecentral.com", look for Remington, 597 page.
Lots of pics and useful info.
__________________
Never beat your head against the wall with out a helmet |
January 16, 2013, 02:38 PM | #4 |
Senior Member
Join Date: September 15, 2005
Location: Oregon
Posts: 1,033
|
I'll take a look at mine this evening if you don't have an answer by then.
|
January 17, 2013, 09:10 AM | #5 |
Junior Member
Join Date: January 7, 2013
Posts: 4
|
thanks all for the replies so far... I'll also check out the rimfirecentral site.
|
January 21, 2013, 08:46 AM | #6 |
Junior Member
Join Date: January 7, 2013
Posts: 4
|
just to update everyone....
turns out this is a bushing/nut from the trigger linkage. Apparently it is very difficult to re-install once it comes off, but I'm going to give it a try. Worst comes to worst, I'll just call Remington support again now that I am better able to describe the issue. Thanks again. |
February 4, 2013, 03:37 PM | #7 |
Junior Member
Join Date: February 3, 2013
Posts: 1
|
So what ended up happening? I think I have the same problem but I don't know how the bushing would have came lose since all I did was take the trigger assembley off of the action. I called Remington and the guy said to try firing, which I did today and it seemed to shoot okay.
|
February 4, 2013, 05:09 PM | #8 |
Junior Member
Join Date: January 7, 2013
Posts: 4
|
bsaf: check out these links.....
http://www.rimfirecentral.com/forums...hlight=linkage http://www.rimfirecentral.com/forums...hlight=linkage |
Thread Tools | Search this Thread |
|
|