The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old February 19, 2010, 07:48 PM   #2601
psyfly
Senior Member
 
Join Date: April 27, 2007
Location: Texas
Posts: 932
Okay, an attempt at pictures of the top-break .38:

".38 Safety Hammerless 3rd Model, manufactured from 1890 to 1898"?

BTW, it isn't (unfortunatelly) mine. It belongs to a friend.





Thanks,

Will
__________________
Show me the data

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
psyfly is offline  
Old February 19, 2010, 10:14 PM   #2602
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
Will - Yes, that appears to be what I thought it was. The larger of the two sideplate screws appears to be missing. Also, it looks like the barrel may have been shortened after it left the factory. Except for a very small number of original special-order 2" barreled guns, the shortest standard barrel length was 3.25" and yours appears a good bit shorter than that. The other thing that suggests that is that the front sight should be pinned through the barrel rib and I don't see a pin in these photos.
FlyFish is offline  
Old February 19, 2010, 11:26 PM   #2603
av8r64
Junior Member
 
Join Date: February 19, 2010
Location: Oak Hills Ca.
Posts: 5
Old S&W? "I GOTS TO KNOW"

Hey FlyFish, Heres the pic its a swing out cyl. 6in. barrel top sight is missing thanks for the help .Av8r64

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
av8r64 is offline  
Old February 19, 2010, 11:34 PM   #2604
av8r64
Junior Member
 
Join Date: February 19, 2010
Location: Oak Hills Ca.
Posts: 5
old S&W?

FlyFish , its also .38cal ,6 rounds kinda rough but i would like to have it restored in the future .Thanks again av8r64
av8r64 is offline  
Old February 20, 2010, 09:16 AM   #2605
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
av8r64 - I believe you have the target variation of the .38 Military and Police Model of 1905, 4th Change. Many of the basic fixed-sight M&Ps were manufactured (production continued from about 1915 to 1942), but the target models, with square butt frame and adjustable target sights, were somewhat rare and are therefore more valuable. As you noted, yours is unfortunately missing the rear sight and also the thumb latch (I'm also not sure if those are the original grips - they should have a raised diamond around the screw holes). I don't know about the availability of parts.

It's not possible to pin down the actual year of manufacture because SCSW just lists the 1915 (at SN 241704) to 1942 (SN 1000000) range with no further information. You can get an idea by interpolating between those two numbers, but it will only be an approximation.
FlyFish is offline  
Old February 20, 2010, 03:18 PM   #2606
drddrd
Junior Member
 
Join Date: February 20, 2010
Location: Wisconsin
Posts: 4
Serial Numbers

New to the thread. Hoping to get dates on the following S&Ws.

Model 64-3 AVA7853
Model 66-2 AEC2136
Model60 R258279

Thanks for the help.
drddrd is offline  
Old February 20, 2010, 03:53 PM   #2607
av8r64
Junior Member
 
Join Date: February 19, 2010
Location: Oak Hills Ca.
Posts: 5
old s&w?

Thanks FlyFish, for checking on this for me your a great help,thanks again av8r64
av8r64 is offline  
Old February 20, 2010, 04:28 PM   #2608
d7kaylor
Junior Member
 
Join Date: February 20, 2010
Posts: 2
.38 spl

Hi guys, I too, need help with my .38 spl. The ser. nu. is 399175 on the butt. it has pat. dates '06, '09, '14 on top of the bbl. fixed sight. Could you give me a date on this piece. I only have one S&W so i don't want to invest in the ref. books. Thanks, Dan
d7kaylor is offline  
Old February 20, 2010, 06:24 PM   #2609
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
serial #517xxx
Av8r64,

FWIW, there's a comment in the SCSW of a purchase of guns between 1927 to 1930 with serial numbers falling in the 500000 to 630000 range.

Quote:
Model 64-3 AVA7853
Model 66-2 AEC2136
Model60 R258279
Model 64-3 AVA7853 = ~1987.
Model 66-2 AEC2136 = 1984.
Model60 R258279 = 1979/80.

Quote:
need help with my .38 spl. The ser. nu. is 399175 on the butt. it has pat. dates '06, '09, '14 on top of the bbl. fixed sight.
.38 Military and Police Model of 1905, 4th Change. SN's ran from 241704 in 1915 to 1000000 in 1942. Your serial number is likely during the 1920's.

Jim
laytonj1 is offline  
Old February 20, 2010, 06:52 PM   #2610
drddrd
Junior Member
 
Join Date: February 20, 2010
Location: Wisconsin
Posts: 4
Numbers

laytonj1 Thanks!
drddrd is offline  
Old February 20, 2010, 08:26 PM   #2611
d7kaylor
Junior Member
 
Join Date: February 20, 2010
Posts: 2
.38 spc.

Thanks Jim. Dan
d7kaylor is offline  
Old February 20, 2010, 09:35 PM   #2612
av8r64
Junior Member
 
Join Date: February 19, 2010
Location: Oak Hills Ca.
Posts: 5
old S&W?

Laytonj1,thanks for the additional info i was thinking 1920era so thats good news,thanks again av8r64



As the Beaver once said "GOLLY JEEPERS YOU GUYS ARE SWELL"
av8r64 is offline  
Old February 21, 2010, 12:55 PM   #2613
onebadscrambler
Member
 
Join Date: November 3, 2009
Location: Fruitland Park, FL
Posts: 36
search. Would anyone out there care to tell me year of manufacture for a SW model 64-2. Number is 1D55406. Thank you.
__________________


JQpublic,
1979-80 by the S/N
The 64-2 was produced in 1977 and appears the 64-3 started production the same year. I do not know if they produced both models for a period of time.
Please comment Flyfish or Layton.
onebadscrambler is offline  
Old February 21, 2010, 01:22 PM   #2614
skydog1979
Member
 
Join Date: February 21, 2010
Posts: 32
Hoping for some help with these two guns.
1. Barrell says 38 s&w special CTG. It has target sights. 6 1/2 " barrell. It has these n umbers in the yoke area S 104XXX. These numbers also appear on the cylinder. There is also a Letter D in the yoke area and the numbers 226XX.

2. This gun says 45 cal. model 1955. It is also 6 1/2" long at the barrell with target sights. The numbers in the yoke area and cylinder are S 160XXX. In the hinged area appears G737XX with the number 7 below the string of letters.

Both guns say Made in U.S.A. Marcus Registradas Smith and Wesson Springfield Mass.

I will post photos as well.
These belonged to my father and I don't know what I have or what kinf of value they may have.
Thanks for your help. I appreciate it.

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
skydog1979 is offline  
Old February 21, 2010, 03:40 PM   #2615
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
skydog1979 -

S104XXX: S&W used the "S" prefix for 12 different models built on the "N" or large revolver frame, but only one of them was chambered in .38 Special: the .38/44 Outdoorsman Model of 1950, which became the Model 23 in 1957 when model numbering began. Yours was made in 1954. Nice. Very nice.

S160XXX: 1955 .45 Target Model, the precursor to the Model 25. The one you have dates from 1956-57. Also very nice. I have one about 9 years younger than yours, by which time they had started using the "N" prefix. It's one of my favorite range guns - I load .45 Auto Rim for it (I'm one of the oddballs who hates using moon clips).

Value depends a lot on condition, and the gun (guns? - I can't really tell if it's one gun or two) in the photos appear to be in great shape, particularly for its (their?) age. With the run-up in revolver prices lately, I think you're looking at several hundred, perhaps close to a grand for each.

BTW, you correctly identified the "S" prefix numbers as the serial numbers. The other numbers stamped in the yoke cutout, and sometimes elsewhere, are so-called "assembly numbers" used to keep track of fitted parts during the manufacturing process.
FlyFish is offline  
Old February 21, 2010, 04:05 PM   #2616
skydog1979
Member
 
Join Date: February 21, 2010
Posts: 32
Thanks alot. It is really nice of you to help me. It is a good feeling knowing I have such nice, intersting revolvers.
Here are other pictures for the .38

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
skydog1979 is offline  
Old February 21, 2010, 04:51 PM   #2617
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
Yeah, those are two really nice guns in beautiful condition. I don't believe the grips on the .38 are original (or correct for the age of the gun) - they should have the little raised diamond around the screw like the grips on the .45. The diamond was dropped in 1967-68.
FlyFish is offline  
Old February 21, 2010, 06:18 PM   #2618
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
JQpublic,
1979-80 by the S/N
The 64-2 was produced in 1977 and appears the 64-3 started production the same year. I do not know if they produced both models for a period of time.
Please comment Flyfish or Layton.
The -2 was a 2" tapered barrel and the -3 was the heavy barrel versions. Both were produced concurrently until they became -4 and -5 versions with the next update in 1988.

Jim
laytonj1 is offline  
Old February 21, 2010, 08:41 PM   #2619
onebadscrambler
Member
 
Join Date: November 3, 2009
Location: Fruitland Park, FL
Posts: 36
Thanks for the additional information Layton. I learned something new today.
Danny
onebadscrambler is offline  
Old February 22, 2010, 08:15 AM   #2620
Birdseye
Junior Member
 
Join Date: September 19, 2008
Posts: 10
Hi folks. My copy of the Standard Catalog is sorta old and these guys are newish. Could you provide some dates?

Thank you.

648-1 BR50xxx
629-4 BRL 7xxx
66-5 CEA6xxx
Birdseye is offline  
Old February 22, 2010, 08:48 AM   #2621
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
Birdseye -

648-1 BR50xxx: 1994 (Should be BRS (i.e., letter "S"), not BR5)
629-4 BRL 7xxx: 1994
66-5 CEA6xxx: 2000
FlyFish is offline  
Old February 22, 2010, 08:59 AM   #2622
Birdseye
Junior Member
 
Join Date: September 19, 2008
Posts: 10
Thank so much, I appreciate your help.
Birdseye is offline  
Old February 22, 2010, 08:20 PM   #2623
ketan
Junior Member
 
Join Date: February 22, 2010
Posts: 4
I am trying to identify my great-grandfather's revolver. He was a police chief back in the early 1900s. I'm afraid I'm not even sure of the model or caliber, so any help here would be GREATLY appreciated.

This is a top-break, safety hammerless revolver (I think). The only markings I have found are the serial number on the bottom of the butt (61xxx) and again on the inside of the chamber. There is also "Smith & Wesson Springfield Mass U.S.A. PAT'D FEBY. 20. 77. DEC. 19. 77. MAY 11. 80. SEPT. 11. 85. OCT. 2. 85. TWO AUG. 4. 85" engraved in the top of the barrel.

ketan is offline  
Old February 22, 2010, 09:27 PM   #2624
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
ketan: You have a .38 Safety Hammerless 3rd Model. About 73,000 were made between 1890 and 1898. It looks to be in very nice shape for a gun of that age, and is probably worth somewhere in the range of $600 to $700.
FlyFish is offline  
Old February 22, 2010, 09:42 PM   #2625
ketan
Junior Member
 
Join Date: February 22, 2010
Posts: 4
FlyFish-
Thanks so much for the identification and info. And for the quick response!
ketan is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.58659 seconds with 11 queries