The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools Search this Thread
Old May 8, 1999, 08:06 AM   #1
Harley Nolden
Staff In Memoriam
 
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
Is there a difference of mfg's from the Allen Rifle and the Allin Rifle?
Who made them?
Are there any other Names one might find these rifles?
Harley Nolden is offline  
Old May 8, 1999, 02:28 PM   #2
Harley Nolden
Staff In Memoriam
 
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
There is sometimes confusion between these rifles so thought I would bring it up at the forum.
The Allen Drop Breech Rimfire Rifle, by Allen & Wheelock, Ethan Allen & Co. was made from 1860-1871. Total quantity estimated at 1,1500 to 2000 copies. It was made in a variety of callibers, 22 thru 44 rimfire. Single shot, Part round part octagon barrels, lengths vary from 23" to 30". The breech opened by lowering the trigger guard, the motion ejecting the emty cartridge; hammer cocked manally: Unique elevating rear sight on the left frame.

Iron mountings, blued barrel, the frame, hammer and trigger guard were casehardened Frames observed in flat and rounded configurations. Walnut buttstock and forend, the latter sometimes fitted with a metal cap. Some were fitted with swivels on the butt stock and forend.
Harley Nolden is offline  
Old May 8, 1999, 02:51 PM   #3
Harley Nolden
Staff In Memoriam
 
Join Date: January 8, 1999
Location: Brunswick,GA USA
Posts: 1,884
ALLIN:
Other Names: Trapdoor Springfield
Springfield, Allin
Country of Origin: United States:
Designer: Erskine Allin
Master Armor @ Nat. armory

1864: Original conversion of existing rifle muskets was completed in April 1865 resulting in the recommendation of the Spencer repeater and the single-shot Peabody. The end of the Civil War removed the need to act with any great haste, discontinuing any further testing on the project.

1865: The proto-type Allin rifle appeared in the summer of 1865, performing well enough for substantial quantities to be ordered for field trials. About 5,000 .58 caliber rimfire rifles were made in the Springfield factory in 1865-66. They were adapted in 1863 pattern cap-lock hinged laterally at the front of the action. The block could be swung up to reveal the chamber, but the alteration was much too complicated; the ratchet-pattern extractor was weak and the cartridge performed poorly.

1866: The M1865 was soon replaced by a rifle with its own barrel lined-down from caliber .58 to .50 caliber. The extractor was greatly simplified and many detail changes were made. Trials still favored the Berdan as the best conversion system, the Peabody being the best new rifle, but the
.50 Allin was Controversially selected for production.

1872: Re chambering rifles to the new 45-70 CF cartridge

1873: The Model 1873 was the first of the Trapdoor Springfield chambered for the 45-70 cartridge. The Ordnance dept. had determined that standardization of US> small arms in .45 caliber (45-70 Long arms and 45 Colt for hand guns was advisable, effective in 1873.

A feature that helps identify early 1873's is the flush sides or fit of the barrel at the point where it screws into the receiver; hence, the stock recess/channel is straight cut at that point whereas in later trapdoors the receiver was widened and the is a slight two step cutaway in the stock.

The early 1873's (up to 1877) had breech blocks casehardened and quenched in oil which gave them a black look. After 1877 the case hardening process, used water to quench, which gave the brilliant colors.

This is a similar case as with the Rider Rifles, (Remington Rolling Block) where the users gave them another name which became more known than the origianl name of the rifle. Allin (Trapdoor Springfield)

Book of Rifles
hjn
Harley Nolden is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04291 seconds with 10 queries