February 12, 2018, 01:18 PM | #1 |
Senior Member
Join Date: February 10, 2018
Posts: 167
|
Newbe Here, 30-30 Powder?
My first post. I helped my Father reload in the 60s and have just started up again with my adult son. In trying to get a somewhat universal powder for the loads that I need, I bought 4064 for my 30-06, 7 Mag and 6.5 jap. I also bought 3031 for my 25-35, but lost that in a fire. I am now looking at 30-30 with cast 170 gr bullet loads and I cant find anything for 4064. I found one load for jacketed bullets but I dont think I can safely use it with cast. Does anyone know of a safe (moderate load) for cast bullets using 4064? If needed , I will buy more 3031 but I hate to pay as much for shipping as the cost of 1 lb of powder. Any help will be appreciated. Grant.
|
February 12, 2018, 01:34 PM | #2 |
Senior Member
Join Date: December 27, 2017
Posts: 460
|
4064 works, but I am saving for some Leverevolution. Too bad you have to mail order your powder. My new Lyman says 27.0 to 30.5 and lists 4064 as potentially the most accurate for the 170 gra8n bullet. 2.540 OAL. ALWAYS work up from the bottom.
|
February 12, 2018, 02:16 PM | #3 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
No 170's listed, but there is some very old(as in no way the powder lots would be close) cast bullet data for IMR4064. There are several 4064 powders none of which use the same data too. Mind you, IMR4064 is not really a cast bullet powder.
https://www.riflemagazine.com/magazi...l63partial.pdf "...for shipping..." Best to buy components locally. Especially powder and primers, but because shipping costs are based partly on the weight, bullets too.. 27.0 to 30.5 is not cast bullet data. Do not use jacketed data for cast bullets. It causes leading.
__________________
Spelling and grammar count! |
February 12, 2018, 02:35 PM | #4 |
Senior Member
Join Date: February 11, 2011
Location: So-Cal
Posts: 786
|
Oh boy, going to be a might tough to find one powder for all the application'a you want. H4831 works for 6.5 Jap., 7mm RM and 30-06, just not for 30-30. Win 748 works well in the 30-30. Curious, you're not able to find/buy powders locally?
|
February 12, 2018, 02:43 PM | #5 |
Senior Member
Join Date: September 6, 2006
Location: Great state of Texas
Posts: 1,077
|
IMR3031 would be a better choice for cast in the .30-30... it's what I use. Generally speaking, you don't want to drive a cast bullet past 1800fps or so unless 1) it has a gas check, and/or 2) you've slugged your bore and the bullets you are using are sized for that bore. Just using 'jacketed' data does not automatically lead your barrel, I use a starting 'jacketed' load for loading cast in my .348WCF, including IMR4064, but I have bullets properly sized for the bore. It's true, overdriving cast bullets can exhibit barrel leading... but that is a typically a product of too much velocity, coupled with a poor bullet choice.
That being said, I show the same 27.0grn IMR4064 starting load for a 170grn jacketed bullet (Speer manual,) I don't see any reason not to give it a try, or reduce that to 25grn and give it a go. I wouldn't load more than 5 rounds or so, as a tester. Your rifle will tell you in pretty short order if it likes it or not. My experiences with a shorter barrel and IMR4064 (in my 20" .348) have not been favorable, the velocity was down compared to IMR3031, all else being equal, but the only way to tell is to try it in your rifle... a little longer barrel with the smaller bullet diameter might work very well.
__________________
_______________ "I have this pistol pointed at your heart!" "That is my least vulnerable spot." |
February 12, 2018, 02:44 PM | #6 |
Senior Member
Join Date: August 18, 2016
Posts: 206
|
Lee reloading manual has a lot of cast bullet data, will check for you later tonight.
|
February 12, 2018, 02:48 PM | #7 | |
Senior Member
Join Date: September 6, 2006
Location: Great state of Texas
Posts: 1,077
|
Quote:
__________________
_______________ "I have this pistol pointed at your heart!" "That is my least vulnerable spot." |
|
February 12, 2018, 07:39 PM | #8 |
Senior Member
Join Date: February 10, 2018
Posts: 167
|
Wow, I didnt expect so many reply,s so quickly. I think I am going to like this forum. I havent actually looked for powder locally. I live in a rural town in California which only has 1 gun shop, and he is only a dealer, not a gunsmith. I will try out my new 170 gr rn mold tomorrow and see if l like the results. It is for gas checks. There is no sense slugging the bore since we have 3, 30-30s in the family, so I will try some reduced loads of IMR 4065 and see how I like them. I will probably buy some 3031 since I also have a 25-35 to load for also. I loaded some 6.5 Jap last week with 34 gr of 4065 and 139 gr jacketed bullets and they seem to shoot well so I will stick to that. I will have other questions about the 6.5 but I will start another thread about that. I dug out my Dads 60 year old press and scales and some rifles that havent been shot in years and I am having fun. Thanks _____Grant.
|
February 13, 2018, 01:09 AM | #9 |
Senior Member
Join Date: March 24, 2006
Location: Northern Utah
Posts: 705
|
My first reloading many years ago was for the 30-30. I got some 3031 powder and it worked well. Still use that powder for the 30-30. Have fun!
|
February 13, 2018, 02:47 AM | #10 |
Senior Member
Join Date: January 7, 2008
Posts: 3,224
|
4064 is just about ideal for the 30-'06, and will likely work pretty well in the others, but the 7mm Magnum really needs something slower burning, like H-4831 or IMR-7828. Perhaps the most versatile rifle powder is IMR 4895, which is just about perfect for 30-30. I think that you really need two powders: A Magnum rifle powder that will also work well for the heaviest bullets in the 30-'06; and a medium burn-rate powder for everything else, including the 30-'06 with all but the heaviest bullets.
|
February 15, 2018, 08:06 PM | #11 |
Senior Member
Join Date: December 24, 2017
Location: Wichita, Kansas
Posts: 220
|
Not many people shoot cast lead in 30-30. To much is given up. Not like a 45-70 where velocities (and pressures), even on the +P end barely overlap the low end of starting loads for a 30-30 . A bitsy little 308 caliber 170 grain bullet, to work effectively, velocities are generally around 2000 fps and upward to 2400 fps. Too fast for cast lead even gas checked.
So, even if they are intended only as a plinker loads, a plinker cast load in my 45-70 will still hit like a freight train and be a useful hunting load if only at closer distance. One can load and shoot a 45-70 from 900 fps to 1800ish using cast lead 405gr bullets. A 1200 to 1600 fps 170 grain cast load from a 30-30, what can you do with that? But plink. Yeah, I guess you could hunt with a 170gr cast bullet at 1600 fps, but, as I said, you are giving up a lot. Plus, then, you wind up needing to shoot cast and jacketed in the 30-30 whereas a 45-70 shooter can shoot only cast and still plink, hunt or take on a t-rex if need be. Cannot be said for the 30-30. The 30-30 needs jacketed bullets to be a good hunting round (which it is no doubt). My current loads for 30-30, 160gr FTX with 34.0gr of Lever revolution powder, CCI LR primer, Winchester nickel brass and the other 170gr Sierra JFP with 34.5gr of Lever Revolution powder, CCI LR primer and Winchester brass. My 45-70 gets cast lead, my 30-30 gets jacketed, both exclusively. 3C Last edited by 3Crows; February 15, 2018 at 08:27 PM. |
February 15, 2018, 08:09 PM | #12 |
Junior member
Join Date: June 13, 2017
Posts: 429
|
3Crows what do you get for the 170gr load fps wise?
|
February 15, 2018, 08:23 PM | #13 |
Senior Member
Join Date: December 24, 2017
Location: Wichita, Kansas
Posts: 220
|
Howdy, I am getting around 2200 fps from my 336SS REP and about 2175 from my 336 Texan JM. Both are 20 inch Micro Groove barrels. I am still working these loads using the data from the Hogden site.
Note I made a correction, I am 34.5gr of LR powder on the Sierra 170gr load. 3C |
February 15, 2018, 09:49 PM | #14 |
Senior Member
Join Date: November 21, 2013
Location: New Hampshire
Posts: 1,691
|
Bought myself The Henry 30-30 in brass and did some 170 gr loads using my trusty W748 ball powder. Love this powder simply for the smooth precise metering. W748 is a great do all powder from AR15 gas gun to 30 cal bolt action.
__________________
"To be old an wise you must have been young and stupid" |
February 16, 2018, 10:11 AM | #15 | |
Senior Member
Join Date: September 6, 2006
Location: Great state of Texas
Posts: 1,077
|
Quote:
__________________
_______________ "I have this pistol pointed at your heart!" "That is my least vulnerable spot." |
|
February 16, 2018, 10:13 AM | #16 | |
Junior member
Join Date: June 13, 2017
Posts: 429
|
Quote:
|
|
February 16, 2018, 10:25 AM | #17 |
Senior Member
Join Date: February 11, 2011
Location: So-Cal
Posts: 786
|
2400fps/mv from a 30-30 using a 170gr bullet out of a 20" barrel? Whao, I'm not to sure about that. Not even using LR powder.
|
February 16, 2018, 10:29 AM | #18 | |
Junior member
Join Date: June 13, 2017
Posts: 429
|
Quote:
|
|
February 16, 2018, 11:02 AM | #19 |
Senior Member
Join Date: February 11, 2011
Location: So-Cal
Posts: 786
|
LOL! Ok, that did have me wondering. I load the Hornady 170gr FN over a hefty charge of Win 748 and get about 2150 over the screens. Accurate and hard hitting. Mod 94.
|
February 16, 2018, 05:56 PM | #20 |
Senior Member
Join Date: January 7, 2008
Posts: 3,224
|
As far as ball-type powders go, I have had excellent results with W-748, BL-C(2), and I am currently trying out some of the new LVR powder. All three seem to be a lot alike. With the extruded IMR-4895, which I really like, I trickle-weigh every charge. But not so with the three afore-mentioned ball powders, as they meter rather consistently from the powder measure.
|
February 16, 2018, 06:22 PM | #21 |
Senior Member
Join Date: December 24, 2017
Location: Wichita, Kansas
Posts: 220
|
The Lever Revolution powder is a ball type and it flows nicely. Here is the load data that drew me to the Lever powder and of course Hogden load data:
http://www.rifleshootermag.com/ammo/..._30-30_030811/ If you read carefully you will see the posted loads in the article were from a 20 inch barrel 336 Marlin. From the article posted above: I see no point in pushing the Sierra 170gr load I made at 34.5gr any higher. I may push the Hornady 160gr FTX a little more. The * given for the 160 FTX, if you read the article, indicate a max. load and the ** indicates the most accurate and useful load. I tend to agree for these from my loadings thus far. Again, the table above is from a 20 inch barrel 336 per the article. 3C |
February 16, 2018, 06:59 PM | #22 |
Senior Member
Join Date: February 11, 2011
Location: So-Cal
Posts: 786
|
3 Crows, that is an interesting article. I'm good with my load above,but, dang, I may have to give that Leverevolution a whirl. You know, self education and all.
|
February 16, 2018, 08:35 PM | #23 |
Senior Member
Join Date: June 23, 2004
Location: Ohio
Posts: 5,676
|
I have a bag full of 150gr gas check lead bullets for the 30-30. So how does load data vary with gas checked lead versus non gas check, if any? Use the same powder loads as no gas check or what? I understand they are somewhat reduced loads compared to jacketed. BTW everyone appreciates the handy 20 inch carbine barrel, and that is all I ever see available, but then loading manuals use a longer barrel most of the time to achieve better MV. But that is annoying as pretty much you need a scarce or vintage gun to get the longer barrel.
__________________
Your gun is like your nose, it is just wrong for someone else to pick it for you! Last edited by Tom2; February 16, 2018 at 08:40 PM. |
February 16, 2018, 11:27 PM | #24 |
Senior Member
Join Date: September 12, 2015
Location: Issaquah WA. Its a dry rain.
Posts: 1,774
|
Gas check usage is up to you. All based on velocity, powder burn rate and how it effects erosion of the bullet in the bore. If ya feel ya need it, use it.
__________________
Just shoot the damn thing. |
February 17, 2018, 01:12 AM | #25 |
Senior Member
Join Date: January 7, 2008
Posts: 3,224
|
If you compare Hodgdon LVR and BL-C(2), looking at the pressure data and velocity per grains powder, they look to be nearly the same powder. Probably good substitutes for each other when you can only find one of them.
|
Thread Tools | Search this Thread |
|
|