The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old February 21, 2021, 03:21 PM   #1
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
frozen selector switch on an AR

A few weeks ago I put my AR into the safe cocked with the selector on SAFE.

I took it out yesterday to clean it, and after putting it back together, the selector was frozen. It simply would not budge out of Safe.

I finally had to release the pistol grip and drop the detent completely out.

When I put it all back together it was fine.

Any ideas what would cause that?
ghbucky is offline  
Old February 21, 2021, 04:43 PM   #2
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 21,824
Detent hole too deep? Drilled wrong?
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old February 21, 2021, 11:20 PM   #3
HWS
Member
 
Join Date: July 1, 2018
Posts: 90
I have had trouble with selector switches. But my trouble resulted from non-mil spec selector switches. For $10.00 you can get a new one at Del-Ton just to make sure.
HWS is offline  
Old February 22, 2021, 01:51 PM   #4
RKG
Senior Member
 
Join Date: June 18, 2009
Location: Boston
Posts: 562
Be sure the disconnector spring isn't inserted upside down.
RKG is offline  
Old February 22, 2021, 03:37 PM   #5
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
Quote:
Be sure the disconnector spring isn't inserted upside down.
Wait, what? There is an up/down to them? How do I know which way is correct?
ghbucky is offline  
Old February 22, 2021, 08:46 PM   #6
krunchnik
Senior Member
 
Join Date: October 27, 2010
Location: Lakeland,TN
Posts: 220
Spring looks the same on both ends-what are we missing??
__________________
THE CROW
krunchnik is offline  
Old February 23, 2021, 01:06 PM   #7
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 21,022
The wider end is down in the trigger and the narrower end is in the disconnector notch. There's a photo you can see here when you scroll about 3/4 of the way down.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old February 23, 2021, 01:34 PM   #8
krunchnik
Senior Member
 
Join Date: October 27, 2010
Location: Lakeland,TN
Posts: 220
OP is talking about the pin that fits into the notch in the SAFETY SELECTOR-not the disconnect on the trigger group.
__________________
THE CROW
krunchnik is offline  
Old February 23, 2021, 02:45 PM   #9
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
Quote:
OP is talking about the pin that fits into the notch in the SAFETY SELECTOR-not the disconnect on the trigger group.
Yes, correct.

The detent had locked the select lever. For reasons I cannot fathom, it would not move, yet it freely dropped out when I released the pistol grip.

And after I put it back together, with the same detent and spring, it has functioned fine.

I've ordered replacement detent and spring, but that's a hail mary, I'm clueless what caused it. I guess a bit of grit inside the tunnel could lock it up.
ghbucky is offline  
Old February 24, 2021, 01:51 AM   #10
stagpanther
Senior Member
 
Join Date: March 2, 2014
Posts: 11,655
Was the rotation of the selector stiff and gritty before? Sometimes the location of the holes as well as the width of the selector can make a difference. The trigger rockers in the well and the rear shelf of the trigger rides against the round part of the selector and is "released" to firing on the flat on the selector. I've run into a couple of times trigger designs that if the pins drifted a bit changing the contact angle between the trigger and selector or a piece of debris--like a chunk of blown primer gets caught up in that area--it can create a wedge effect preventing easy rotation of the selector.

Stealing the picture from the link above--this is the contact area between the trigger and selector.

Attached Images
File Type: jpg Screen Shot 2021-02-24 at 1.59.17 AM.jpg (59.0 KB, 319 views)
__________________
"Everyone speaks gun."--Robert O'Neill
I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk!

Last edited by stagpanther; February 24, 2021 at 02:09 AM.
stagpanther is offline  
Old February 25, 2021, 01:29 PM   #11
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
I would expect that if it was debris in that contact area, there would have been 'wiggle' in the selector. When I removed the detent, the selector went completely free, no resistance at all.

I'm pretty convinced that something was preventing the detent from compressing and locked the selector in place.
ghbucky is offline  
Old February 25, 2021, 02:27 PM   #12
stagpanther
Senior Member
 
Join Date: March 2, 2014
Posts: 11,655
Quote:
I would expect that if it was debris in that contact area, there would have been 'wiggle' in the selector. When I removed the detent, the selector went completely free, no resistance at all.
Receiver cross pins can do the same thing, often it is because of an ever-so-slight offset in the holes between the upper and lowers; it doesn't take much. Anyway sounds like you got it fixed.
__________________
"Everyone speaks gun."--Robert O'Neill
I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk!
stagpanther is offline  
Old February 25, 2021, 03:11 PM   #13
Maxwell Haus
member
 
Join Date: December 14, 2016
Posts: 113
Detent in backwards, after taking it out it was put back in correctly is my guess.
Maxwell Haus is offline  
Old February 25, 2021, 03:15 PM   #14
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
Quote:
Receiver cross pins can do the same thing
I did replace the trigger a while back, so those pins were removed and re-installed. Is there a way to confirm that they are properly aligned?
ghbucky is offline  
Old February 25, 2021, 06:36 PM   #15
stagpanther
Senior Member
 
Join Date: March 2, 2014
Posts: 11,655
Depending upon the trigger design, there are generally notches in the trigger and hammer pins designed to go through in a particular orientation so that the legs of the hammer spring can sit in them. Not all trigger groups use them though. If the pin drifts enough (hence the popularity of after-market anti-rotation/drift pin sets) the orientation of the trigger or hammer can be altered.
__________________
"Everyone speaks gun."--Robert O'Neill
I am NOT an expert--I do not have any formal experience or certification in firearms use or testing; use any information I post at your own risk!
stagpanther is offline  
Old March 10, 2021, 09:33 AM   #16
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 21,824
Field expedient repai - take a file and round off the top of the detent.

Note: with the right parts, you shouldn't have to do any of this. It should work the first time. Non-spec parts?
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old March 10, 2021, 01:22 PM   #17
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
It is a milspec lower from Anderson.

I replaced the mil-spec trigger with a drop in, and used the same pins.

I've checked the selector several times since that happened and it has worked perfectly every time.
ghbucky is offline  
Old March 11, 2021, 04:45 PM   #18
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
Quote:
Detent in backwards, after taking it out it was put back in correctly is my guess.
Safety detents only go in one way.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old March 11, 2021, 05:56 PM   #19
Maxwell Haus
member
 
Join Date: December 14, 2016
Posts: 113
Quote:
Originally Posted by Scorch View Post
Safety detents only go in one way.
Correct, if you know which end goes in first .
Maxwell Haus is offline  
Old March 11, 2021, 08:38 PM   #20
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
Quote:
Correct, if you know which end goes in first .
If you try to put it in the other way, the safety falls out.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old March 12, 2021, 05:32 AM   #21
Geezerbiker
Senior Member
 
Join Date: March 20, 2011
Location: Willamina, OR
Posts: 1,908
Is it possible that the OP mixed 2 types of lubricants that don't mix well? I've see some oils turn to polymer when mixed with incompatible chemicals.

Tony
Geezerbiker is offline  
Old March 12, 2021, 09:23 AM   #22
ghbucky
Senior Member
 
Join Date: June 12, 2020
Posts: 1,177
Quote:
Is it possible that the OP mixed 2 types of lubricants that don't mix well? I've see some oils turn to polymer when mixed with incompatible chemicals.
I use hoppes to clean and a breakfree lube product. Same stuff I use on everything else. Every time this thread gets updated it reminds me so I go check to see if the selector is working. Fine again.

One thing I neglected to mention was that the rifle had been at the range and had something like 60 rounds through it and there were no issues with the selector there. It went into the safe and wasn't touched again until I took it out and after cleaning the selector wouldn't budge.

The only thing that I can think of is that there was some debris in the tunnel that wouldn't let the detent compress. I can't imagine any other scenario. Nor can I imagine how anything got into the tunnel.

I guess this was one of those freak, one in a million set of events that happened.
ghbucky is offline  
Old March 13, 2021, 01:53 AM   #23
Geezerbiker
Senior Member
 
Join Date: March 20, 2011
Location: Willamina, OR
Posts: 1,908
Gremlins.

Tony
Geezerbiker is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.15084 seconds with 11 queries