|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
March 4, 2018, 11:56 AM | #1 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
S&W Model 64 4" to 3" Barrel
|
March 4, 2018, 01:47 PM | #2 |
Senior Member
Join Date: December 29, 2010
Location: Shoshoni Wyoming
Posts: 2,713
|
If it were mine I would not use stainless. I's use a steel you can blue.
Silver front sights can be hard to see and align, and they are hard to use MOST of the time. Black sights are WAY BETTER. |
March 4, 2018, 01:53 PM | #3 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
Kitchen knives and scissors would be too hard. Measure the width and go buy an SS screw or bolt. Screws and bolts are a lot softer and can be filed.
Like Wyosmith says, SS sights, or any sight on polished SS, will disappear in sunlight. And the front sight must match the height of the groove.
__________________
Spelling and grammar count! |
March 4, 2018, 02:10 PM | #4 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
Ahhh hardware. I'm off to Lowes to see what I can find. A large washer ??
The sight will be the same height as S&W's front sight measured from the top of the bore. If I had the proper equipment I would cut a dovetail and use a black aftermarket sight. This stainless steel revolver came with a SS front sight so I see no problem using SS for a replacement. I'm not really a shooter so I don't much care about the practicality. I do shoot a Ruger Vaquero sometimes with SS sights and they seem ok to me. Thanks for the help. I wasn't thinking hardware ...DUH |
March 4, 2018, 09:09 PM | #5 |
Senior Member
Join Date: May 4, 2001
Posts: 7,478
|
If you can't find a suitable piece locally, there's some good online sources for small quantities of stainless stock:
http://www.onlinemetals.com/merchant...ep=2&top_cat=1 https://www.mcmaster.com/#standard-s...heets/=1btwvvh https://www.boltdepot.com/Washers.aspx?nv=l Email and they can tell you the thicknesses of the washers. Most front sights are about 1/10 inch thick. Measure the old sight. |
March 5, 2018, 07:48 AM | #6 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
Thanks
If I cant find what I need at my local Fastenal, I have some more sources/ |
March 5, 2018, 07:51 AM | #7 |
Senior Member
Join Date: January 2, 2015
Location: The swamps of WNY
Posts: 753
|
I can mail you a piece of 1/8" stainless 304. Free.
David Sent from my Pixel 2 using Tapatalk |
March 6, 2018, 11:00 PM | #8 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
Thanks but I already got some thick 2" diameter stainless steel washers from my local Grainger store. The new sight is the most difficult part of this modification. I really want it to look right.
|
March 13, 2018, 03:53 PM | #9 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
|
March 13, 2018, 08:57 PM | #10 |
Senior Member
Join Date: August 5, 2012
Location: Carthage, NY
Posts: 231
|
Looks like a nice job on that sight, nice job all the way around.
|
March 20, 2018, 10:29 AM | #11 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,832
|
Field test time.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
March 21, 2018, 02:35 PM | #12 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
|
March 21, 2018, 04:59 PM | #13 |
Senior Member
Join Date: April 23, 2017
Posts: 239
|
Get some black paint for that front sight; that will help your shooting. Nice revolver, I have one with a 3" tube and love it.
__________________
Young guys should hang out with old guys; old guys know stuff. |
March 22, 2018, 11:55 AM | #14 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,061
|
Nice work.
Should you change your mind about the site color, there is cold bluing available for stainless. It's really more charcoal gray than black but would improve sight contrast. Mask off the barrel with rubber tape and use one of the Badger airbrush style abrasive blasters to get a good matte surface on the sight before applying the stainless cold blue. Masking is advisable for that as well. I use liquid asphaltum engraver's etch resist from an art store for that kind of masking.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
March 22, 2018, 07:14 PM | #15 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
Thanks but the 56% silver brazing filler will not respond to bluing so I would have a silver line around the bottom of the sight.
|
March 22, 2018, 07:34 PM | #16 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,061
|
Brownells used to sell a blacking agent for silver solder. I don't know if it's still there or not. But an alternative is Cerakote or one of the other paint-on finishes.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
March 22, 2018, 09:17 PM | #17 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
The filler I used was not silver solder. Silver solder has maybe 4% silver and is worked at 400/500 degrees F. I used a 56% Silver Brazing filler (expensive) worked at 1200 degrees F.
I'm not a fan of painted firearms I don't care who does the work. I can understand why someone might like the fact that the firearm does not need to be disassembled to paint it. Actually you can Cerakote a loaded gun. Hahaha Thanks for your interest. |
March 24, 2018, 10:14 AM | #18 |
Senior Member
Join Date: March 26, 2005
Location: Osborn, Missouri
Posts: 2,697
|
arguebus357, I think you did a very nice job on your pistol. I too dislike paint on guns, paint on my house, tractors and barn is OK but not on my guns.
|
March 24, 2018, 12:05 PM | #19 |
Senior Member
Join Date: December 5, 2001
Location: Indiana
Posts: 233
|
That turned out nice. I really like how a three inch barrel handles on a revolver.
|
March 25, 2018, 06:57 AM | #20 |
Senior Member
Join Date: December 19, 2016
Location: Atlanta, Georgia area
Posts: 455
|
^^^^^^
Yep, I agree. These 64's with the heavy barrel and small lightweight 38 spl. cylinder are quite nose heavy. It's surprising how much difference 1" of barrel makes. |
March 25, 2018, 09:22 PM | #21 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,061
|
Arquebus357,
I believe you are referring to what is usually called silver-bearing solder (2-4%), which is technically a soft solder with conventional lead or tin-base. Silver solder, though not a technically correct term, has long been an abbreviation of "silver hard solder" or brazing alloy, and that is what Brownells used to sell its blacking material for. I am guessing you use Harris Safety-silv 56 or a copy of it. I use that and their 45T product. All good stuff. Here's one for pure silver that may work, but I would contact the maker before trying it. This is another option. I agree with you both about the 3" barrel. It's my favorite compromise between compactness and shootability. I've never really been able to get a snub-nose to print well, but a 3" will let me shoot the ten ring out of a 25-yard target. The difference is surprising.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
|
|