The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Thread Tools Search this Thread
Old August 4, 2013, 11:16 PM   #1
Senior Member
Join Date: July 1, 2013
Location: Douglasville, Ga
Posts: 4,615

so i was giong to order my sizing dies and first i wanted to get my barrels slugged. now, let me say beforehand that i know to only do this with a wooden dowel or something plastic so to not scratch my barrel, but i didn't. so i grabbed a few of my 9mm barrels and i used a flathead screwdriver and just tried to keep it aligned on the back of the bullet, but i didn't. i have about a 3/4 inch long and deep enough to notice scratch in the rifling of the barrel. starts about 1/2 inch into the barrel and stops. i know i'm a [email protected]#$, i don't need a lecture, but is there anything i can do? should i even worry about it?

p.s. i switched to a phillips head............
skizzums is offline  
Old August 4, 2013, 11:45 PM   #2
Senior Member
Join Date: April 28, 2012
Location: NY
Posts: 184
I dunno
I'd say go out and try it. Worst thing I can see , it's gonna suffer in accuracy.
Valerko is offline  
Old August 5, 2013, 11:42 AM   #3
Senior Member
Join Date: February 7, 2012
Posts: 514
What is "slugging" ?
SpareMag is offline  
Old August 5, 2013, 01:13 PM   #4
Senior Member
Join Date: March 13, 2011
Posts: 455
Ugh. Thinking about that makes me queezy... Not much you can do about it. Shoot it to see how accuracy was affected. You may need a new barrel, you will definitely have to work harder to keep the gouge free of lead and copper deposits. Sorry about your luck. Rule #5: Always use the right tool for the job.

Slugging is a method to check the inside diameter size of your bore.
John 20:29 Jesus said to him, “Thomas, because you have seen Me, you have believed. Blessed are those who have not seen and yet have believed.”
iamdb is offline  
Old August 5, 2013, 01:22 PM   #5
James K
Join Date: March 17, 1999
Posts: 24,189
Like the first scratch on a new car. What's done is done, it won't cause any problems, and after while you will forget all about it.

Jim K
James K is offline  
Old August 5, 2013, 01:28 PM   #6
Senior Member
Join Date: September 12, 2002
Location: Twin Cities, MN
Posts: 3,739
It's incredible the amount of information online. You can go to Youtube put in 'slugging a pistol barrel' and get videos on what it is and how to do it.

Here's just one but there are many out there.
DaleA is offline  
Old August 7, 2013, 01:39 PM   #7
Join Date: June 4, 2013
Location: Nashville, TN
Posts: 57
Ouch! I hope it shoots straight after that injury. Let us know how it functions.
EveryCaliber is offline  
Old August 7, 2013, 03:47 PM   #8
Senior Member
Join Date: February 23, 2005
Posts: 12,921
If the accuracy suffers....or it just aggravates you ......buying a new barrel is not the end of the world...
BigJimP is offline  
Old August 7, 2013, 03:57 PM   #9
Aguila Blanca
Senior Member
Join Date: September 25, 2008
Location: CONUS
Posts: 9,781
Fortunately, we are in the Semi-Automatic handguns forum and not the High Power Rifle Competition forum. I doubt you'll see the effect at typical handgun shooting distances, unless you're a competitive bullseye shooter -- in which case you wouldn't be shooting 9mm anyway.

Shoot it and see how it goes. As noted, if there is a serious deterioration in accuracy, barrels can be bought for most any semi-auto handgun people are likely to be shooting.
Aguila Blanca is offline  
Old August 7, 2013, 04:04 PM   #10
Strafer Gott
Senior Member
Join Date: May 12, 2011
Location: New Mexico
Posts: 1,315
There's all kinds of scratches. Shoot some jacketed bullets and iron it back out. Only the high spots matter. If it doesn't affect accuracy, don't tell a soul.
The problem with experience is you get the test first, then the lesson.
Strafer Gott is offline  
Old August 7, 2013, 04:14 PM   #11
Senior Member
Join Date: September 22, 2012
Location: Marriottsville, Maryland
Posts: 1,291
You might want to smooth the scratch out with a cloth patch that has JB Bore Bright on it. Send the cloth patched rod through the muzzle, so as in order to not over polish the chamber with JB paste.

A brass rod might be better for slugging; along with a rubber mallet --- that is --- if a wooden dowel may not work.
That rifle hanging on the wall of the working class flat or labourer's cottage is the symbol of democracy. It is our job to see that it stays there."

--- George Orwell

Last edited by Erno86; August 7, 2013 at 04:21 PM.
Erno86 is offline  
Old August 9, 2013, 05:33 PM   #12
Senior Member
Join Date: July 1, 2013
Location: Douglasville, Ga
Posts: 4,615
i still haven't shot it, i will test it out on monday morning and let you know if i can tell any difference. i have heard that those extremely expensive barrel lubes can fill in scratches and pits and actually bond to the metal, could be b.s. though. il let you all know on sunday. thanks for everyones input.

p.s. i doubt i'm a skilled enough shooter to really tell a difference. i wish i had done some group tests with it beofre the scratch to have something to compare it to.
skizzums is offline  
Old August 10, 2013, 09:46 AM   #13
Senior Member
Join Date: September 28, 2008
Posts: 10,447
Shall we take bets on the results?
My bet will be that there's no problem, whatsoever.
Other than the aggravation of seeing it, every time you look down the barrel.

I once acquired a cheap 30-06 rifle that looked every bit like a truck gun.
You know, the kind that looks like it actually fell off the truck.
The barrel was atrocious, with rust pits and scratches.
The previous owner(s) must have alternated between never cleaning it, or getting completely carried away with the cleaning rod.
But it didn't know how ugly it was and, surprisingly, turned out to be quite the shooter.
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Old August 24, 2013, 04:37 PM   #14
Senior Member
Join Date: July 1, 2013
Location: Douglasville, Ga
Posts: 4,615
well, i don't know who's going to lose money on this. but apparently a small scratch at the base of the barrel causes BETTER shooting. you heard it hear first folks. i'll will post intriguate graphs and data later. i'll be showing a youtube vid on how to scratch your barrel just right to optimize mil-spec MOA. i have coined it "tactical barrel grazing"

p.s. if anyone still cares, it didn't make a diff. thanks
My head is bloody, but unbowed
skizzums is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 07:35 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.08514 seconds with 9 queries