The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Thread Tools Search this Thread
Old January 29, 2012, 05:35 PM   #1
Senior Member
Join Date: November 5, 2008
Posts: 153
Dillon SD - Thinking of moving to a progressive after 20 years of loading

Hi Guys,

I need some advice before switching to a progressive.

I'm considering the Dillon Square Deal because I only load 38 special.

The one thing holding me back however is the fear of a squib load from a 'no charge' I may not detect. I'm so accustomed to doing visual checks before seating bullets -am I being over concerned?

Thanks, Racingsnake
Racingsnake is offline  
Old January 29, 2012, 06:07 PM   #2
Join Date: March 4, 2005
Location: Ohio
Posts: 13,825
Lots of guys mount lights on these things to better see down into the case to check the powder charge. That said, because the charge is dispensed automatically, it's hare to get a squib except or a double in a round at the powder station unless it's during some kind of jam. At that point you want to take the case in that position out and set it aside for separate processing, then continue with the rest.

If it still concerns you, then you also have the option to move to a basic 650, which has a fifth station for a Dillon powder check die.
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member
Unclenick is offline  
Old January 29, 2012, 06:11 PM   #3
Senior Member
Join Date: September 28, 2008
Posts: 10,447
With a good light source above the press, you will be able to easily see if powder is in the case before adding the bullet.
I have a small light mounted on my SD press that shines directly down the case, at the third die, where the bullet is put in the case.
To be able to use a powder check alarm, though, would require a press with an extra die position.
But I trust my eyes more than a device.
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Old January 29, 2012, 06:29 PM   #4
Junior member
Join Date: January 1, 2007
Location: Idaho
Posts: 2,282
Anecdotally, I have had my SD since before they were SD Bs loaded thousands of rounds, .44 spec., .45 auto, and.38 spec. I don't recall either a double charge or no charge load. Mine has been if not trouble free, pretty close and Dillon has a great warranty.
salvadore is offline  
Old January 29, 2012, 08:03 PM   #5
Senior Member
Join Date: January 16, 2011
Location: North Bend, OR
Posts: 741
I've been loading 357 mag with a SD B with no problems
Vance is offline  
Old January 29, 2012, 08:10 PM   #6
Senior Member
Join Date: February 16, 2009
Location: John's Creek, Georgia
Posts: 328
I have three sets of twin flourescent 2x4 ft lights in the drop ceiling in my loading room which is off premise from my home. I can easily see everything in the bullets from powder to bullet and last primer. Yes, lights do make a good addition to safe reloading of bullets. I have a set of Twin Dillon SDB's as I only also reload only Pistol Bullets.
Steviewonder1 is offline  
Old January 29, 2012, 10:51 PM   #7
Senior Member
Join Date: May 16, 2008
Location: Coastal South Texas
Posts: 557
I found a small light with a flex arm and clip on the end. I clipped it on the primer tube and flexed it to see right down into the cases at station 3. Works like a charm. Got the light at TSC. The SDB is a great press and you won't be sorry you got it. I have a matched pair, one for 9mm and one for .45.
jfrey is offline  
Old January 30, 2012, 08:08 AM   #8
Senior Member
Join Date: March 22, 2002
Location: In The Hardwoods
Posts: 1,114
It's a simple thing to leave the locator pin out of station 3 & check the case before seating the bullet. I do this with mine.

LAH is offline  
Old January 30, 2012, 09:32 AM   #9
Senior Member
Join Date: November 5, 2008
Posts: 153
Thank you guys
Racingsnake is offline  

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -5. The time now is 10:29 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent:
Contact Us
Page generated in 0.06846 seconds with 9 queries