The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old February 16, 2000, 08:45 PM   #1
jhoth
Junior Member
 
Join Date: February 9, 2000
Posts: 7
I recently obtained a Thompson/Center, New Englander , 50 cal rifle in very poor condition. It looks as if it hasn't been cleaned for years. The exterior of the barrel has lost bluing in places from rust. Is there any hope for any type of reconditioning of the barrel to somewhat decent condition? Or is it at cause? I plan to take it to a local gunsmith for assessment. Any suggestions you can give will be appreciated.
jhoth is offline  
Old February 17, 2000, 12:35 AM   #2
Alex Johnson
Senior Member
 
Join Date: February 16, 2000
Location: Grand Forks, ND
Posts: 812
Lots of times the rusting you see in the bore isn't as bad as you would at first think. First make a safety check with the ramrod to make sure there is not a charge in the gun (if you aren't familiar with this procedure have somebody show you how). After this you can soak the bore with a good penetrating oil WD-40 works fine you want to loosen up the rust a bit before the next step. After this you can try steel wool on a cleaning 45 caliber cleaning jag. Keep scrubbing and adding fresh steel wool and oil until you think the rust is gone, then work at it some more. Clean out the bore periodically with a cotton patch and more oil and check the progress with a bore light. When you can no longer see significant residue on a clean patch you can stop. Certainly there will be some pitting, but if your lucky you may still get hunting accuracy out of the barrel. Of course, the worse the pitting is the harder it will be to clean the gun in the future. Another alternative is to buy one of the fast twist replacement barrels that are made for the TC's. These can be had for about $120 and will allow you to shoot conicals with excellent accuracy, if you are into the conical game.

------------------
"A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed."-Second Amendment to the Constitution
Alex Johnson is offline  
Old February 17, 2000, 09:22 AM   #3
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Jhoth, for the interior of the barrel, Alex gave some good advice. The rest of the metal can be reblued. You can either have this done or turn it into a project for yourself. George
George Stringer is offline  
Old February 17, 2000, 07:29 PM   #4
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
If you can find the right wrench, I recommend pulling the breech plug and doing the job right. If you do, though, be careful. Use a lot of penetrating oil and don't ruin the plug or twist it off.

Jim
James K is offline  
Old February 17, 2000, 09:29 PM   #5
7th Fleet
Senior Member
 
Join Date: January 28, 2000
Posts: 1,469
By all means, pull the breech plug, that way you can see what you really have. TC makes a special tool for that job and it is relatively inexpensive. As far as the exterior of the barrel, the best finish is obtained by browning it. Not only is it more traditional but it is more durable and the end results if done right look really great. Birchwood Casey makes a browning solution that you use by taking a propane torch and heating the barrel and applying the browning to the hot metal. I have a TC that I browned and it looks fantastic...7th

------------------
SUPPORT YOUR LOCAL POLICE, KEEP THEM INDEPENDENT.
7th Fleet is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06415 seconds with 7 queries