The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old December 29, 2001, 08:25 PM   #1
buzz11648
Junior Member
 
Join Date: December 29, 2001
Location: waynesboro,PA
Posts: 9
win. m1200 field barrel cut down

Hello all,

I recently purchased an old win. m1200 12g. 2.75 ch. field shotgun. I was considering cutting down the barrel myself to 20". It currently measures 29.5". If i did cut down the barrel would there be a risk of the barrel cracking or exploding? I'm not familiar with the legality of this and want to keep it legal. Also, i cannot find any production info. on this model other than intro. in 1964. Any experiences with 8 shot mag ext. would also be helpful. Want to make a home defense gun and 100.00 didn't seem bad for a base gun.

Thanks all and happy blasting!
buzz11648 is offline  
Old December 29, 2001, 10:00 PM   #2
maxwayne
Senior Member
 
Join Date: March 10, 2001
Posts: 401
A great gun, I have had mine since 63. The feds say the barrel has to be 18 inches, so cut it a little long to be safe. There should be no safety problems with a shorter barrel. Use a file to smooth out the rough edges after you cut it.
maxwayne is offline  
Old December 30, 2001, 07:35 AM   #3
Dave McC
Staff In Memoriam
 
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,812
I've cut down several bbls, and oft regretted same, but you've little to lose here.IME the 1200 needs to be kept clean, and grunge will turn it inoperative in short order. Clean, it's a good, reliable shotgun.

Measure from the breech face to the muzzle, the new length HAS to be over 18" or you're in deep trouble with the Feds.

Also, while more shells isn't a bad idea, an absolutely stock short shotgun is a defensive tool of amazing capability.Start off with light loads and work up...
Dave McC is offline  
Old January 1, 2002, 02:49 PM   #4
buzz11648
Junior Member
 
Join Date: December 29, 2001
Location: waynesboro,PA
Posts: 9
model 1200 barrel

Thanks guys, i like the pattern of the stock 30" full choke barrel so i think i"ll leave it alone.
buzz11648 is offline  
Old January 2, 2002, 02:50 PM   #5
plateshooter
Senior Member
 
Join Date: September 29, 1999
Location: N.E. Ohio
Posts: 522
You may find that the gun shoots high with the cut off barrel if you put the bead directly into the new end. My smith solders or tigs a block on the barrel and threads a hole for the bead into that. You can then adjust your point of impact by filing down the block and reinstalling the bead until your pattern is centered or where you want it to be. If you cut off the barrel, take the shortened gun and site down the barrel. Then without moving, have someone hold the piece you cut off on the end and you will see what I mean.
__________________
Make a hole
plateshooter is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06653 seconds with 7 queries