The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old July 15, 2001, 07:18 PM   #1
Redneck2
Senior Member
 
Join Date: April 24, 2000
Location: Northern Indiana
Posts: 519
How to set OAL and interchanging cases ???

Went to a local dealer and got a good price on 200 grain LSWC's for the 45 acp ($17.95 per 500). They appear to be the same or very similar to the #452630 as listed in the Lyman manual.

Now I know that "similar, close to, about the same" don't cut it a lot of times in reloading.....so, how do I set OAL with an unknown bullet? In fact, how do you ever know for sure unless the bullet is the EXACT one specified in the manual?

Only way I can see is to find a bullet that you have info on, measure and establish the seating depth into the case, and then set all others to the same depth (into the case) taking into account the variance in length of the bullet. Is this correct??

CASE BRAND...I know that substituting rifle cases can have a rather dramatic effect on pressure. I have a good supply of mixed manufacturer cases for the 45. With relatively mild loads (6.3 of Unique) can I safely mix the brands? I would assume so as the cases are not nearly as full as most rifle loads but want to check first.. Thanks in advance.
Redneck2 is offline  
Old July 15, 2001, 09:01 PM   #2
ArmySon
Staff Alumnus
 
Join Date: April 14, 2000
Posts: 2,926
If you're off a couple thousandths with .45 ACP, it's not going to make that much of a deal.
__________________
Your friends will forgive your mistakes. Your enemies will kill you for it.
ArmySon is offline  
Old July 15, 2001, 11:08 PM   #3
swifter...
Senior Member
 
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
Redneck2,

When I was shooting action matches, I loaded many thousands of 200 gr SWC .45s by seating them so I had about 1/32nd" of bullet shoulder sticking out from the case mouth. This moves the headspace from the case mouth to the bullet shoulder and a crush fit, but improves reliability. Don't sweat the length when you do this, its damn near self-adjusting. Just don't go much over 7.0 of Unique.
Tom
__________________
There are damn few situations so screwed up that adding government to them will not make 'em worse...
The best homeland security is an armed & informed citizenery!
Molon Labe!
swifter... is offline  
Old July 16, 2001, 12:17 AM   #4
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
Trial and error for a bullet with no data. What I've always done was start light & long, increase depth until feed reliability is attained, then work up the powder charge after that.
No KB's yet.
Edward429451 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07371 seconds with 9 queries