The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old June 28, 2001, 05:22 PM   #1
STEVE M
Senior Member
 
Join Date: February 7, 1999
Location: TN. USA
Posts: 607
help with Timney trigger/Mauser

George or Jim (or anyone ;with experience), I need help in a hurry. I just put my new Timney trigger (sportsman model) in my 98 Mauser. The cocking piece falls when the bolt is shoved fast, and if the trigger is pulled when the safety is on, and then you disengage the safety is will fire. According to the directions I need to file or grind down surface #9. The drawing is unclear as to what part #9 is.It would seem to be the front of the cocking piece on the bolt (that engages the sear). My understanding of this is that I need to shorten this (front to back) so that it will engage the trigger's sear latter. Is this correct? I don't mind filing and grinding but I want to make sure that I am on the right part, and have the mechanics down correctely.
Thanks, Steve
STEVE M is offline  
Old June 28, 2001, 08:12 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 20,001
The front of the cocking piece is the part to grind; you have to let the sear rise to keep the striker cocked. Be sure you keep the angle at 90 degrees and proceed slowly. Note that if too much metal is removed, you could have problems moving the safety out of the fire position.

But once you grind on it, the cocking piece may be unusable with the original sear, so make sure you intend for the Timney job to be permanent. Mostly those triggers go in OK with no grinding needed, so you might also check the general condition of the rifle and whether its parts are mismatched.

Jim
__________________
Jim K
James K is offline  
Old June 29, 2001, 05:14 AM   #3
STEVE M
Senior Member
 
Join Date: February 7, 1999
Location: TN. USA
Posts: 607
I think the parts are ok as far as matching. I had a gunsmith install a Bueller type safety on it and check the rifle over when I first got it. The rest of the installation with easy except for the problems noted. This will be permenant, I see no reason to ever go back to the awful trigger that it came with. Thanks, Jim
__________________
MOLON LABE!
I've joined the 300.
STEVE M is offline  
Old June 29, 2001, 10:39 AM   #4
stuckatwork
Senior Member
 
Join Date: March 3, 2000
Posts: 217
Steve M,

Before you take a file to anything, make sure that that the adjustments on the trigger are set properly. There should be two allen screws held in place by small nuts. One is travel the other is pull. Look on the instructions and see which is which. Just becasue the instructions say "set at the factory, do not adjust" doesn't mean that someone didn't have a bad day. If your trigger pull is set too light, or the travel adjustment is to shallow, you will get the symptoms your are describing.

I am assuming that this is a surplus Mauser. Have you disassembled the bolt and cleaned away all that heavy grease? I have seen some of the bolts so gummed up with coagulated grease that the safety would not fully engage, the cocking mechanism would not turn and a bunch of other irratants. When replacing the grease in the bolt, I recommend the blue bearing grease made for wheel bearings. It will not harden up with heat and age.

God luck
__________________
These are the words of Stuckatwork.
They don't represent the views or opinions
of my employers. They aren't that clever.
stuckatwork is offline  
Old June 29, 2001, 08:45 PM   #5
STEVE M
Senior Member
 
Join Date: February 7, 1999
Location: TN. USA
Posts: 607
Thanks for the help guys. A bit (actually a lot) of filing and grinding and the new trigger is in. I've checked for all of the problems listed in the instructions with no problems. I've got it adjusted down to a nice 2-1/4lb pull with very little take up, it is sweet!
Can you think of any other safety checks that I should/can do before a call this finished?
thanks again, Steve
__________________
MOLON LABE!
I've joined the 300.
STEVE M is offline  
Old June 30, 2001, 08:55 PM   #6
James K
Staff
 
Join Date: March 17, 1999
Posts: 20,001
Sounds good, but here are three quick checks (with empty gun, of course):

1. With the bock cocked and the safety on, pull the trigger, hard. Release the safety. The firing should not drop.

2. With the bolt cocked and the safety on, drop the butt hard on a solid surface. Do the same with the safety off. The firing pin should not drop.

3. Work the bolt as fast as possible (safety must be off). The firing pin should not drop.

If those tests are OK, I see no problems in that area.

Jim
__________________
Jim K
James K is offline  
Old July 1, 2001, 02:13 PM   #7
STEVE M
Senior Member
 
Join Date: February 7, 1999
Location: TN. USA
Posts: 607
Thanks Jim, It passed with flying colors. If you thought I asked questions this time just wait until I start putting on the backup sights ( this is the begining of a sorta-scout project).
__________________
MOLON LABE!
I've joined the 300.
STEVE M is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08350 seconds with 7 queries