The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 10, 2014, 05:29 AM   #1
wkillette
Junior Member
 
Join Date: March 26, 2014
Location: Mooresville, NC
Posts: 10
Using loading table data

I am currently looking for load data with Unique for 40 S&W. I have 165 gr bullets and am finding a lot of data for 170 gr bullets. In some manuals they say you can move up a loading table and use the next table higher as loading data for a lighter bullet. Example use the 170 gr table for 165 gr.

What is the popular view on this and has this posed any problems for anyone.

Thanks in advance.
wkillette is offline  
Old June 10, 2014, 09:42 AM   #2
Gadawg88
Senior Member
 
Join Date: March 2, 2013
Location: Georgia
Posts: 101
Did you check the Alliant online load data. They have a load listed using Unique and a 165 gn speer gdhp. Generally speaking, what you suggest should be safe. All other things being equal, a heavier bullet will take less powder than a lighter bullet. You don't want to go the other way. That could get you in some trouble.
Gadawg88 is offline  
Old June 10, 2014, 10:05 AM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,086
It is ok.
If you can tell the difference between a 165 and a 170 grain bullet in typical bulk pistol ammo, you get the Princess and the Pea Award.
Jim Watson is offline  
Old June 10, 2014, 03:50 PM   #4
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 2,974
With thin shoes, I can feel a pea sized rock under me shoes.

165 vs 170 grain is less important than that.
__________________
The word 'forum" does not mean "not criticizing books."
"Ad hominem fallacy" is not the same as point by point criticism of books. If you bought the book, and believe it all, it may FEEL like an ad hominem attack, but you might strive to accept other points of view may exist.
Are we a nation of competing ideas, or a nation of forced conformity of thought?
Clark is offline  
Old June 10, 2014, 04:55 PM   #5
std7mag
Senior Member
 
Join Date: June 23, 2013
Location: Central Pennsyltucky...
Posts: 328
With the usual warnings of not using a load too hot, etc....
This is for reference use only. I'm not a reloading manual.

But if I was, I would tell you....




According to the load data from my Lee die set Unique is 6.3-7.2 gr. with a 165 gr. XTP.

Alliant gives max load only for the Speer Gold Dot 165 gr. at 7.2 grains of Unique.
std7mag is offline  
Old June 10, 2014, 05:59 PM   #6
Jim243
Senior Member
 
Join Date: January 5, 2009
Location: Just off Route 66
Posts: 4,520
Quote:
What is the popular view on this and has this posed any problems for anyone.
OK, here is the rule of thumb, as the weight of the bullet goes down the weight of powder goes up.

As the weight of the bullet goes up, the weight of the powder goes down.

That being said, the load for a 170 grain bullet will be fine for a 165 grain bullet since it would normally use more powder.

HOWEVER !!!!!!! The min and max for a 40 S&W is not all that big and does not allow for much variation SO BE CAREFUL and test, test & test to be sure. You could end up with an UNDER pressure load. If you start in the MIDDLE of the powder weight for the 170 grain load, you should be safe.

Jim
__________________
Si vis pacem, para bellum
Jim243 is online now  
Old June 12, 2014, 08:56 PM   #7
reynolds357
Senior Member
 
Join Date: December 10, 2012
Posts: 2,264
Should be fine, but just be sure it will feed with a full magazine jammed in it.
reynolds357 is offline  
Old June 12, 2014, 09:35 PM   #8
wkillette
Junior Member
 
Join Date: March 26, 2014
Location: Mooresville, NC
Posts: 10
thanks for all the replies, it has been helpful
wkillette is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06862 seconds with 7 queries