The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old January 25, 2014, 08:05 PM   #1
pollo
Member
 
Join Date: March 6, 2013
Location: NC
Posts: 40
30-06 Scope Sliding in Rings

Hello all, I have a scope that is sliding forwards in its rings. I had to shim the scope a lot to get enough elevation; I had to shim it so much that I had 2 shims under the base (if I could have put more shims under the base, I would have, but the screws weren't long enough) and 2 shims in the rings themselves (which I learned the hard way, not to do). Anyways, I noticed that the shims were sliding out while shooting, so I decided to take the scope back off, and epoxy the shims to the rear scope ring, then remount the scope. When I got the scope off, I noticed that the scope was distorted a little where the rear ring was, but I decided to give it another chance; I glued the shims to the rear base, then remounted the scope. So, I shot it again today, and noticed that the epoxy seal/seam had split in two, one piece was up the scope an eighth of an inch, while the other part of the seam was still on the bottom side of the scope ring (sorry this is hard to explain in words). Or in other words, I had found evidence that the scope was STILL moving. I have it on Leupold low rings (I lost the package it come in so I don't know specifically what kind of Leupold rings they are). The rings are on a one piece scope base that came with the gun (it is a Marlin XL7 30-06). What to do, what to do?

Thanks for any help.

Pollo
pollo is offline  
Old January 25, 2014, 09:00 PM   #2
Snyper
Senior Member
 
Join Date: December 16, 2013
Location: Eastern NC
Posts: 731
Quote:
What to do, what to do?
Take the shims out of the rings. and get longer screws so all the shimming is under the base.

Unless you're shooting VERY long range all the time, I'm not sure why you need shims at all
__________________
One shot, one kill
Snyper is offline  
Old January 25, 2014, 09:01 PM   #3
n8ball
Member
 
Join Date: December 13, 2013
Location: stafford ct
Posts: 39
did u locktite the screws the first time u tried it?
n8ball is offline  
Old January 25, 2014, 09:27 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,837
The old solution, if all else fails, was rosin, as in baseball's "rosin bag".

Jim
__________________
Jim K
James K is offline  
Old January 25, 2014, 09:48 PM   #5
pollo
Member
 
Join Date: March 6, 2013
Location: NC
Posts: 40
Okay, thanks guys. I'll try everything y'all listed.

Thanks

Pollo
pollo is offline  
Old January 26, 2014, 02:15 AM   #6
hoghunting
Senior Member
 
Join Date: March 27, 2006
Posts: 1,358
Or you could try the Burris Signature rings and you'll probably need the offset insert kit. The polymer inserts will align the scope to the barrel and will correct shimming the base. The inserts will also keep the scope from moving.

http://www.midwayusa.com/find?userSe...ignature+rings
hoghunting is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06712 seconds with 7 queries