The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Curios and Relics

Reply
 
Thread Tools
Old January 17, 2014, 01:05 AM   #1
Aso544
Junior Member
 
Join Date: January 16, 2014
Posts: 1
C&R Pistols.... Need Some Info

I know this one is a Colt New Service 455 Elly. It is a pre WW1 revolver that was produced commercially and also for the British government. I curious to see how to determine if its been converted to shoot the 45 Colt as I know that reduces the value along with the missing original grips. The serial number is 52210. Any thoughts on the value of this revolver.







This other pistol seems to be a hammered copy of a SW Lemon Squeeze. I can't quite tell what the engraved emblem is on the receiver or what emblem on the grips matches a manufacture from back in the day. Again any info and value will be greatly appreciated.


Aso544 is offline  
Old January 17, 2014, 10:17 AM   #2
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 5,602
Quote:
Originally Posted by Aso544
I['m] curious to see how to determine if its been converted to shoot the 45 Colt...
I've not personally seen a converted Colt, but I've examined several converted Smith & Wesson revolvers, and all of them had obvious signs of machine work to the rear face of the cylinder. .455 Webley (aka Eley) has a much thinner rim than .45 Colt, so material was usually removed to allow the cylinder to close. Since this work was usually done by military surplus dealers who intended to resell the revolvers for very low prices, they had no incentive to pay for quality work, and this modification is generally pretty easy to spot.

Judging by the lack of machining marks and the matching appearance of the finish on the rear cylinder face, I'm going to go out on a limb and say that I DON'T think this gun has been converted.

FWIW S&W's from this era had shouldered chambers- i.e. the rear portion of the chambers was case diameter, but the forward portion was bullet diameter, with an obvious step in between. Therefore, converting a S&W would also involve reaming the chambers deeper. However, IIRC .45-caliber Colts of this vintage were not built this way; the chambers were bored straight through. (Someone PLEASE correct me if I'm wrong.)
__________________
"Smokey, this is not 'Nam. This is bowling. There are rules... MARK IT ZERO!!" - Walter Sobchak

Last edited by carguychris; January 17, 2014 at 10:19 AM. Reason: minor reword...
carguychris is online now  
Old January 17, 2014, 11:07 AM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,300
The Colt Question can be settled by attempting to insert a .45 Colt cartridge. If it chambers and the cylinder closes, then it has been converted. If not, not.

The only "modern" Colt with the "bored through cylinder" business was the early 1917 .45 ACP which relied on its moon clips. Later guns and, I think, a lot of replacement cylinders, had normal headspace stops and cylinder throats.

I think I can see a shoulder to throat diameter in the chamber at 6 o'clock. If so, it looks pretty short and is likely still .455.


The topbreak is one of many European knockoffs of Smith & Wesson, probably Spanish. It is the original "Two dollar pistol" than which there is very little hotter. There were a lot of small makers in Spain before Franco rationalized the industry there. Even the Zhuk reference book will say "Eibar, maker unknown." But I have seen that trademark SOMEWHERE, just don't recall it.
Jim Watson is online now  
Old January 17, 2014, 01:58 PM   #4
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,605
The top break is a pretty little thing....

I like that it is blued and not plated.
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old January 17, 2014, 11:12 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,852
Chris is right on the conversions, but I think that cylinder has been converted, not by reaming but with a simple countersink, maybe even something like a cone shaped cartridge case reamer. The rear of the chambers looks like that and it would probably have been enough given the small rim of the .45 Colt.

Of course, Jim Watson has the real answer; try a .45 Colt round.

On the breaktop, I agree on its being Spanish; I am sure I have seen that grip marking somewhere, but and find it now.

Jim
__________________
Jim K
James K is offline  
Old January 18, 2014, 06:42 AM   #6
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
Gangarossa's book shows pictures (taken from the ALFA catalog reprint) of two revolvers with the star trademark and says "probably Garate, Anitua or Orbea Hermanos."
gyvel is offline  
Old January 19, 2014, 02:54 PM   #7
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,852
Could be, but Orbea usually used the intertwined "OH" and Garate, Anitua used an intertwined "GAC".

Jim
__________________
Jim K
James K is offline  
Old January 21, 2014, 08:53 AM   #8
highpower3006
Senior Member
 
Join Date: July 30, 2011
Location: Reno NV
Posts: 437
I'm going to go with the thought that it has been converted. I have a New Service (in .45 Colt) and there is no bevel on the rear of the chambers.

This would have been done to allow the slightly larger rim of the .45 Colt cartridge to headspace properly. As has been mentioned, the easy way to determine if it was converted is to try and insert a cartridge.
highpower3006 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08293 seconds with 7 queries