The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 30, 2013, 07:02 PM   #1
el_chupo_
Member
 
Join Date: April 4, 2013
Posts: 36
pistol case damage - OK to reload?

Just getting started in reloading, as I havent been able to find powder locally until last week...

I have been cleaning some range brass recently in preparation, and noticed that quite a few of the cases have a small dent in the side of the case. I assume this is where the case is hitting the ejection port or similar, as I see a small dent on many .223/5.56 brass as well.

Is it OK to reload this, or should I toss anything like that out?

I can get pictures if needed.

Thanks!
el_chupo_ is offline  
Old December 30, 2013, 07:47 PM   #2
John D
Senior Member
 
Join Date: October 24, 2000
Location: California
Posts: 254
I wouldn't load dented brass. Brass is too inexpensive (or free!) to use any that might cause problems.
John D is offline  
Old December 30, 2013, 07:50 PM   #3
1stmar
Senior Member
 
Join Date: March 21, 2012
Location: Connecticut
Posts: 1,196
Anything that would cause feeding issues would likely getting addressed during sizing. If dents remain they will fire out and be fine.
1stmar is offline  
Old December 30, 2013, 07:59 PM   #4
YARDDOG(1)
Senior Member
 
Join Date: October 24, 2008
Location: GATOR COUNTRY HA HA HA!
Posts: 690
Run em through your sizer, should straiten right out ; )
Y/D
__________________
There's a GATOR in the bushes & She's Callin my name
>Molly Hatchett<
YARDDOG(1) is offline  
Old December 30, 2013, 08:11 PM   #5
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,093
Size them, shoot them.

Toss brass that has cracks or has primer pockets too large to hold the primer.
__________________
If I'm not shooting, I'm reloading.
Slamfire is offline  
Old December 30, 2013, 09:58 PM   #6
Ozzieman
Senior Member
 
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 4,964
+1 Slamfire
If I threw away every 5.56 case that had a dent (small) I would few left. If it’s a small rounded dent I use them, it’s only the ones that have a crease or has damaged the brass gets tossed.
__________________
“Peace is that brief glorious moment in history when everybody stands around reloading.” – Thomas Jefferson.

Politician's are like diapers.
You need to change them often,,,,, for the same reason!
Ozzieman is offline  
Old December 30, 2013, 10:10 PM   #7
el_chupo_
Member
 
Join Date: April 4, 2013
Posts: 36
Great, thanks guys. I have been tossing any that look bad, but the little dings didnt seem bad...
el_chupo_ is offline  
Old December 31, 2013, 03:44 PM   #8
Damon555
Senior Member
 
Join Date: January 11, 2012
Posts: 124
Brass that has a minor dent can be reloaded without issue....
Damon555 is offline  
Old December 31, 2013, 04:16 PM   #9
buck460XVR
Senior Member
 
Join Date: December 28, 2006
Posts: 2,071
Half the .45 ACP brass I pick up at the range has bites from the ejection port. Even if they don't size out completely, they still shoot well. Deep sharp creases are another thing.
buck460XVR is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07632 seconds with 7 queries