The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 29, 2013, 06:11 PM   #1
papazip
Junior Member
 
Join Date: March 19, 2013
Location: southwest nh
Posts: 12
The Keith in a rifle

Trying to toss Elmer's favorite 44 out of a Handy Rifle without leading.Can it be done?
papazip is offline  
Old December 30, 2013, 05:30 AM   #2
Mike / Tx
Senior Member
 
Join Date: April 8, 2000
Posts: 1,316
The fit will be the primary issue with the lube lasting the lenght being the second.

If I were trying this I would give a couple of sizes a try and not be using anything less than .430" diameter bullets. If your using commercial bullets try those brands which offer a selection of sizes and possibly hardness. Something in a .430 at around a 14BHN should work just fine.

I would also recommend picking up a bottle of Alox as well. If you find your commercial bullets are leading give them a good roll around in some of the Alox before loading. This might help out what ever lube they used to make it to the muzzle.

If your pouring your own and find your getting leading you might look up White Label Lubes and try some of his Carnuba Red. IT is good stuff but needs a little heat to work well in some lubsizers.
__________________
LAter,
Mike / TX
Mike / Tx is offline  
Old December 30, 2013, 10:38 AM   #3
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 2,943
I push a hot-loaded (Ruger-Only) 45 Keith out the end of a 20" `94 Marlin using Alox (stomp, stomp ).
-- no problem at all w/ Lym#2 @ BN:15, so a 44 should be no different.

Make sure that bullet's big enough to seal the bore. Don't even try otherwise
mehavey is offline  
Old December 30, 2013, 11:57 AM   #4
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 1,110
You need to slug the barrel. SAAMI dimensions are different for rifle vs. handgun in .44 magnum, with rifle groove diameters up to .431". Size/purchase bullets that are at least .432" or, about .001"-.002" over the groove diameter of your barrel, for a non-leading load...
__________________
My Anchor is holding fast!
mikld is offline  
Old January 1, 2014, 02:05 PM   #5
papazip
Junior Member
 
Join Date: March 19, 2013
Location: southwest nh
Posts: 12
Thanks for the info,guys. Here I go.....
papazip is offline  
Old January 2, 2014, 07:33 AM   #6
44 AMP
Staff
 
Join Date: March 11, 2006
Location: Upper US
Posts: 11,499
What do you consider Elmer's favorite load?

The one I recall he wrote about most was his 250gr SWC, 22gr of 2400 and standard (not magnum) primers.

Skelton liked that load, but preferred 21.5gr 2400...

These are hot loads, but shouldn't lead, even in a rifle, IF a)the bullet is sized correctly for the bore, and b) it is cast HARD enough.

Lyman #2 alloy should be your baseline for hardness when working with loads at these levels.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better.
44 AMP is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06428 seconds with 7 queries