The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 22, 2013, 04:52 PM   #26
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 2,005
I would always keep a (good!) beam scale on hand for reference and for that day when the electronic fails.

I actually have two beams, one is an Ohaus 505 (yep, back in the day) and a RCBS 10-10 that my brother who got out of reloading gave me.

The 10-10 is the nicer scale but the 505 is quicker so I use that (and it gets banged around a bit as my reloading bench is also my main work bench.

If they both went I would get an RCBS now I guess) 505 again.
RC20 is offline  
Old December 22, 2013, 08:44 PM   #27
Eppie
Senior Member
 
Join Date: January 7, 2010
Location: Houston, TX
Posts: 795
Quote:
RC20 said: I would always keep a (good!) beam scale on hand for reference and for that day when the electronic fails.
This is correct. You can have an electronic but you can't ever totally trust it.
__________________
"Socialized Medicine is the Keystone to the Arch of the Socialist State.” -Vladimir Lenin
"I predict future happiness for Americans if they can prevent the government from wasting the labors of the people under the pretense of taking care of them." - Thomas Jefferson (An early warning to Obama care)
Eppie is offline  
Old December 23, 2013, 11:00 AM   #28
higgite
Senior Member
 
Join Date: October 21, 2010
Posts: 264
Plus a set of check weights. As I discovered (post #22), you can't ever totally trust a beam scale either.
higgite is offline  
Old December 29, 2013, 05:52 PM   #29
wachtelhund1
Senior Member
 
Join Date: January 4, 2007
Posts: 122
I tried electronic scales years ago and thought my RCBS 10-10 balance was more accurate. Several years ago, I purchased a Sartorius electronic scale, this is very accurate + or - .002 of a grain. Not cheap but accurate and fast. At my age, I just can't squint at balance beams anymore. Just don't have any fans on or breath in its direction when weighing a charge. About $300.00.
wachtelhund1 is offline  
Old December 29, 2013, 07:24 PM   #30
Sidewinder72
Senior Member
 
Join Date: November 25, 2008
Location: Kansas
Posts: 130
I have a pact scale that I love. It is about seven years old and has earned my trust. I used a 10-10 for years, but only use for shotgun now. Get yourself a good set of check weights to check readings for accuracy. They are a big time saver. I also have the dispenser to go with scale.
Sidewinder72 is offline  
Old December 29, 2013, 07:27 PM   #31
steveNChunter
Senior Member
 
Join Date: December 14, 2012
Location: Southern Appalachian Mtns
Posts: 1,280
I use a cheap Hornady GS 1500 digital scale. I bought it to get me up and running with reloading, knowing in the back of my mind I'd eventually want something else. I make sure and calibrate it each time I use it and give it time to settle when weighing a charge. A time or two I have seen it not go back to zero when I lift the pan off of it. When it does it, it usually says 0.3 instead of 0.0. I just tap the scale, let it zero, then weigh the charge again. It's almost always within 0.1 of what it was the first time. A little aggravating but for the $20 it cost me I can put up with it till I can upgrade my equipment. If I could quit buying rifles, scopes, bullets, powder, primers, and brass I could have upgraded my whole setup by now. People who say reloading saves money are lying. All you do is shoot more and get more addicted to your hobby. It's a terrible disease
__________________
I have a very strict gun control policy: if there's a gun around, I want to be in control of it. - Clint Eastwood
steveNChunter is offline  
Old December 30, 2013, 12:36 PM   #32
Brutus
Senior Member
 
Join Date: September 11, 2005
Posts: 332
Well so far this new Lyman scale has been working very well keeps right on track with my balance beam. I've gotten into the habit of turning it on for a half hour or so before use as recommended by some of you folks. Doesn't seem to be having any problem with the fluorescent light over my bench and it is plugged into the same receptacle.
__________________
To a man with only a hammer everything looks like a nail.
Brutus is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08157 seconds with 7 queries