The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old October 23, 2013, 10:29 AM   #1
six-gun
Member
 
Join Date: September 20, 2010
Posts: 55
Will A Kydex Holster Mark My XDm?

I'm comparing holsters for my XDm Compact .40. My brother loves the Galco King Tuck and it does get good reviews. My worry is will it scratch my finish? It's the standard, black finish. A Taurus i used to own wound up with scratches on it from a Blackhawk holster. An all leather IWB deep conceal would run around $100 or more though, so I'd prefer the price of the King Tuck. But if it's going to scratch the finish, I'll spend the extra money. So I'd like to hear if anybody has had issues with it scratching.
__________________
"One of the ordinary modes, by which tyrants accomplish their purposes without resistance, is by disarming the people and making it an offense to keep arms."
six-gun is offline  
Old October 23, 2013, 11:43 AM   #2
allaroundhunter
Senior Member
 
Join Date: May 6, 2012
Location: Southeast Texas
Posts: 1,670
Will A Kydex Holster Mark My XDm?

You will get holster wear from any type of holster. Scratches? You shouldn't, but the Blackhawks shouldn't have given them, either.

If your gun is a working gun then get the best holster for the job (and your budget) and let the finish wear normally. You can get it refinished later on.
allaroundhunter is offline  
Old October 23, 2013, 12:56 PM   #3
ripnbst
Senior Member
 
Join Date: November 24, 2010
Location: Tulsa, OK
Posts: 1,385
It will show wear over time, yes. But this is normal and a part of life. Don't fret about it. Keep the gun and holster reasonably clean and you'll have nothing to worry about.
ripnbst is offline  
Old October 23, 2013, 01:41 PM   #4
ClydeFrog
Junior member
 
Join Date: May 1, 2010
Posts: 5,798
New Kydex or polymer holsters...

I agree with the other TFLers, any polymer or Kydex holster may cause slight wear over time or with excessive "holster work"(a term I heard from a Gander Mountain Academy employee).

When you first get the new Kydex holster, Id loosen up the screws then insert the firearm into it & secure it as needed.
I learned the lesson the hard way with my new Blade-tech holster for my Ruger GPNY, .
ClydeFrog is offline  
Old October 23, 2013, 09:40 PM   #5
tgreening
Senior Member
 
Join Date: February 7, 2011
Location: NE Ohio
Posts: 246
I use a king tuk with an XDM compact and wear, while not non-existent, is fairly minimal.

The way I look at it is, it's a tool, not a show piece. My man concern is it comes out and goes bang when it counts, and I don't care what it looks like getting it's job done.
tgreening is offline  
Old October 24, 2013, 03:17 PM   #6
plateshooter
Senior Member
 
Join Date: September 29, 1999
Location: N.E. Ohio
Posts: 522
I've been making Kydex holsters for several years and when customers ask me that question, my answer is always "yes it will eventually." You can slow the wear down a lot. I use silicone oil I get from Rusty's Rags and it works very well for me. Wipe the inside of the holster with the sheep skin supplied and it keeps the wear down.
__________________
Make a hole
plateshooter is offline  
Old October 26, 2013, 07:35 PM   #7
Kreyzhorse
Senior Member
 
Join Date: April 12, 2006
Location: NKY
Posts: 11,452
Yes.

That said, any holster will eventually cause wear. Plastic holsters will cause that wear faster than leather holsters will.
__________________
"He who laughs last, laughs dead." Homer Simpson
Kreyzhorse is offline  
Old October 26, 2013, 08:09 PM   #8
kutz
Senior Member
 
Join Date: September 24, 2012
Location: New Mexico USA
Posts: 300
It's patina, not wear, it's character, not wear it shows that it works & has been useful & loved!
kutz is offline  
Old October 28, 2013, 09:51 AM   #9
BigTex308
Senior Member
 
Join Date: October 26, 2012
Location: Texas
Posts: 259
Any holster will wear on a gun over time. There's nothing you can do about it.


Personally I see a gun as a tool. I'm not going to abuse it or cause harm to it intentionally but I'm going to be more concerned on how well my gear and gun works than I am about getting a scratch or a little mark on it.


Ike

Last edited by BigTex308; October 28, 2013 at 09:59 AM.
BigTex308 is offline  
Old October 28, 2013, 10:42 AM   #10
George Hill
Staff Alumnus
 
Join Date: October 14, 1998
Location: North Carolina
Posts: 11,547
Good Kydex will wear a finish less than leather. Leather, especially if it's a little dusty, can act like an emery cloth on a finish. Kydex, wipe it clean once in awhile and you will be fine.
__________________
MAD OGRE
George Hill is offline  
Old October 28, 2013, 12:57 PM   #11
ClydeFrog
Junior member
 
Join Date: May 1, 2010
Posts: 5,798
Metalife...

You could spring $78.00 USD or so & get the XDm pistol's upper parts treated with Metalife.
That will protect the pistol's metal parts & reduce the wear. Extra magazines with the service are $10.00 each.
Robar's great NP3 Plus is like the Metalife treatment but it's not cheap; www.robarguns.com .

Clyde
ClydeFrog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08507 seconds with 7 queries