The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old May 12, 2013, 06:29 AM   #1
thedudeabides
Senior Member
 
Join Date: August 22, 2012
Posts: 1,009
Copper brushes

I have really no idea whether it's OK to use these to clean pistols.

Some manufacturers like Sig, essentially say to only use the nylon brush that comes with the gun, others are pretty vague about it and use "high quality" cleaning supplies.

I have an old fouled P220 barrel that I eventually gave in and scrubbed with a liberal amount of Hoppe's no 9 and a copper brush. The gun went from kinda accurate to like new after the cleaning and I can't see any marring or injury to the barrel.

I just feel like the nylon brushes don't clean all of the fouling, and it does eventually build up over time (thousands of rounds).
thedudeabides is offline  
Old May 12, 2013, 05:35 PM   #2
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 5,266
You might not want to clean your ears with them, but it would be hard to imagine that copper or bronze brushes would do any harm to a barrel.
Unless it was maybe from an airsoft.
__________________
Lock the doors, they're coming in the windows.
g.willikers is offline  
Old May 13, 2013, 10:18 AM   #3
weblance
Senior Member
 
Join Date: October 3, 2012
Posts: 643
Lots of guys use copper Chore Boy strands, wrapped around a copper bore brush, to get the really nasty lead fouling out of a barrel. It works well. Copper is much softer than steel, and wont hurt the rifling.

Chore Boy

Last edited by weblance; May 13, 2013 at 10:35 AM.
weblance is offline  
Old May 22, 2013, 08:54 PM   #4
Miss Stana
Member
 
Join Date: May 17, 2013
Posts: 40
I clean with copper brushes, but there is a trick to it. Push the brush in from the breach end, then unscrew the brush and bring the rod back out. Hoppes is a good cleaner to use too. If the bore is really built up, I'll use a more aggresive copper cleaner, like JB Bore paste, but you have to be careful because it will eat your brush. A nylon brush with good cleaner and tight fitting patches works well too. Then when the bore is clean, I like to clean the cleaner out of it. Some cleaners will etch your bore if they are left to sit in the barrel. This is where I get a lot of my supplies http://www.alkalicorp.com/c-13-clean...x?pagesize=100

hope this helps
__________________
My life's goal is to put a rifle behind every blade of grass!

AIC
Custom Rifles
Miss Stana is offline  
Old May 23, 2013, 05:37 PM   #5
Ben Dover
Senior Member
 
Join Date: April 11, 2013
Location: High up in the Rocky Moun
Posts: 195
I haven't seen copper brushes for a long time. All that I see today are phosphor bronze or nylon whoch will not harm your bore in any way.
__________________
The soldier's pack is not so heavy a burden as the prisoner's chains. Dwight Eisenhower
Ben Dover is offline  
Old May 28, 2013, 12:40 AM   #6
rc
Senior Member
 
Join Date: April 28, 2001
Location: CA
Posts: 609
I've used copper and can say they are A OK! I like them better than nylon for good cleaning. I have used stainless ones to remove lead deposits but those are pretty rough and I use them as a last resort. Bronze and Copper are the best for scrubbing a barrel clean without damaging the barrel.
rc is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:08 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06832 seconds with 7 queries