The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old May 11, 2013, 05:40 AM   #1
NSC
Junior Member
 
Join Date: May 10, 2013
Posts: 3
How to remove the butt plate on an Anschutz 1416?

I am trying to remove the butt plate from my Anschutz 1416. I have removed the two screws and there are no other screws evident but the butt plate is still firmly fixed to the stock. I have also carefully tried to prise a knife blade between the butt plate and the stock but only managed to scratch the stock. Any ideas what to do next? The reason I am removing the butt plate is to increase the length of pull by about 2"/50mm (I have long arms!) so any suggestions about other ways to increase the length of pull would also be gratefully received.
NSC is offline  
Old May 11, 2013, 01:52 PM   #2
Dixie Gunsmithing
Senior Member
 
Join Date: April 27, 2013
Location: Ohio
Posts: 847
It should come off. Evidently, there is some stock finish, etc., under the butt plate, that has bonded with the plate itself. Mount the stock in a vise, in a way it wont get scratched. Next, take a rubber mallet, and sharply rap the edge of the butt plate, and see if that will break it loose. If not, try heating the butt plate with a hair dryer, and then giving it a rap.
Dixie Gunsmithing is offline  
Old May 15, 2013, 11:17 AM   #3
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 4,986
Have you checked Anschutz's web site for a manual that could be downloaded? It probably has a parts diagram that'll help.
__________________
US Navy Distinguished Marksman Badge 153
Former US Navy & Palma Rifle Team Member
NRA High Power Master & Long Range High Master
NRA Smallbore Prone Master
Bart B. is offline  
Old May 15, 2013, 11:35 AM   #4
TATER
Senior Member
 
Join Date: November 19, 2002
Location: Mississippi
Posts: 932
Put an old mouse pad or piece of leather down, Just bounce the stock on the floor.
TATER is offline  
Old May 15, 2013, 10:30 PM   #5
Carne Frio
Senior Member
 
Join Date: August 28, 2008
Location: Near Fairbanks Alaska
Posts: 719
Here's a link to a manual with an expanded drawing.
Looks like it should pop right off after removing two
screws.
http://stevespages.com/pdf/anschutz_1416-1516.pdf
Carne Frio is offline  
Old May 16, 2013, 10:04 AM   #6
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,631
Breaking the bond !!

A number of gun manufacturers do a great job of finishing their stocks but provide little or no protection, on the wood, under the buttplate. Some folks think that you don't need to protect this area and that's wrong. In your case, what I suspect, is that yours does have some protection but what that might be, would only be a guess on my part. I have see the normal finishes, Epoxy, contact or rubber cement and Wax. Again, all in an effort to weather seal this end. .....

I'd say to try a "little" heat and see if this loosens the bond. By the way, I have also seen the application of small brads or pins to hold the white spacer, to the stock. Might be a good idea to contact Anschutz and see if they can help. Please come back and let us know how you made out ..

Hang in there and;
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
Pahoo is offline  
Old May 18, 2013, 09:11 PM   #7
NSC
Junior Member
 
Join Date: May 10, 2013
Posts: 3
Thanks for the info and quick reply, it is much appreciated, as you suggested there was a lot of lacquer under the buttplate, I clamped the rifle on a rubber mat, carefully placed a chisel at the point where the buttplate meets the stock, gave the chisel a few light raps with a piece of wood and they separated, I then gently prised the two apart with a butter knife.

Last edited by NSC; May 19, 2013 at 12:27 AM.
NSC is offline  
Old May 18, 2013, 09:14 PM   #8
NSC
Junior Member
 
Join Date: May 10, 2013
Posts: 3
I should say thanks to all the replies and good advice! It is very kind of you all to take the time to assist me with this, have good days!

Last edited by NSC; May 19, 2013 at 12:01 AM.
NSC is offline  
Reply

Tags
anschutz , buttplate , length of pull

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09334 seconds with 9 queries