The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools
Old April 16, 2013, 09:14 AM   #1
Southern Shooter
Senior Member
 
Join Date: May 4, 2005
Location: central Louisiana
Posts: 443
Ruger Flattop Blackhawks .44 Magnum--50th Anniversary Edition

My two sons have these Flattop Blackhawks in 6 1/2" barrels. They are asking about handloading some heavy bullets for backcounty protection in upper Montana and Idaho areas. I have a couple boxes of the Sierra Sports Master 300 grain jacketed soft-points that I could use. These bullets have a sectional density of .232 .

My question is this:

How hot can/should I take these bullets with these guns? I don't want to damage these flattops with loads that are too rough. But, I don't want to under load these Sierra bullets, either. What loads would ya'll charge these bullets up with these guns?

Thanks
__________________
"My plea is that we stop seeking out the storm and enjoy more fully sunlight. I am suggesting that as we go through life we accentuate the positive. I am asking that we look a little deeper for the good, that we still our voices of insult and sarcasm, that we more generously compliment and endorse virtue and effort." Gordon B. Hinckley
Southern Shooter is offline  
Old April 16, 2013, 09:57 AM   #2
Jim March
Senior Member
 
Join Date: February 14, 1999
Location: Pittsburg, CA, USA
Posts: 7,309
They are the same strength as any recent-production SuperBlackhawk. No problem there.

One issue though: the grip frames are a bit small for coping with full-power 44Mag. At a minimum you NEED to get rid of the black plastic "cheesegrater" grip panels and swap for smooth wood - it takes the same grips as a New Vaquero. There are also some oversize (mainly over-length) grips available, don't recall where, or a lot of people splice in SuperBlackhawk or Bisley grip frames on these guns.
__________________
Jim March
Jim March is offline  
Old April 16, 2013, 10:14 AM   #3
newfrontier45
Junior member
 
Join Date: February 23, 2012
Posts: 921
You don't have to baby them. As Jim said they are the same as a late model Super Blackhawk. The shooters will give up due to recoil before you strain the Ruger.
newfrontier45 is offline  
Old April 16, 2013, 12:06 PM   #4
Sharpsdressed Man
Junior member
 
Join Date: June 21, 2009
Location: NE Ohio
Posts: 1,176
I have fired full load 240 JHP's over heavy loads of Win 296 and H110, and the drawback is the lighter weight of the gun, and the old hogleg grip. It looks and carries great, but that combination will punish you a bit. The Bisley grip is better; rubber grips are more absorbent, etc, but both take away from the great looks of the 50th .44 mag Flattop. You might want to loctite the screws all around if you intend to do a lot of shooting with heavy loads. ............................................
Sharpsdressed Man is offline  
Old April 16, 2013, 08:33 PM   #5
GeauxTide
Senior Member
 
Join Date: April 20, 2009
Location: Helena, AL
Posts: 3,072
Hard cast lead will serve much better. As mentioned, the grip of the 50th is not conducive to heavy bullet recoil control. Take a look at Missouri Bullets and pick a Keith style in 250 grains. Much less expensive, too.
GeauxTide is offline  
Old April 17, 2013, 12:04 AM   #6
salvadore
Senior Member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 1,846
I agree with Mr. Tide, a cast bullet is the way to go, something heavy, and Keithlike. Match up the bullet to the throats.
salvadore is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:30 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07068 seconds with 9 queries