The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old April 12, 2013, 04:54 PM   #1
Roshi
Senior Member
 
Join Date: December 21, 2010
Location: Houston
Posts: 202
Pietta Dance Bros. Revolver - Anyone have one

I like the looks of the Pietta .44 Dance Bros revolver at Cabelas but they never put it on sale. By the time you add shipping and tax it is over $ 400 which is more than I'd like to spend on something I've never seen in person.

Do any of you have one? How about a pic alongside a 51 Navy or 60 Army for comparison.
Roshi is offline  
Old April 12, 2013, 05:24 PM   #2
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 687
I have had two. They are about like holding an 1860 army revolver with navy grips. Very well balanced revolver and they shoot good too. Only reason I sold mine was because I got out of C&B guns. Now I just have two 51 navies.
MJN77 is offline  
Old April 12, 2013, 08:08 PM   #3
brazosdave
Senior Member
 
Join Date: September 7, 2012
Location: Copperas Cove, TX
Posts: 300
I agree with you man. I love the looks of it, but the price point is sitting a little bit on the high side for me right now. Would love to pick one up eventually oneday. There's always gunbroker.......
__________________
"I'm your huckleberry, it's just my game"
brazosdave is offline  
Old April 12, 2013, 10:03 PM   #4
Captainkirk
Senior Member
 
Join Date: September 21, 2012
Posts: 137
My buddy had one. He never fired it. I never could get used to the appearance of the shaved recoil shield. Just not my cup o' tea.
__________________
"You gonna pull those pistols, or whistle Dixie?"
Captainkirk is offline  
Old April 14, 2013, 08:21 AM   #5
madcratebuilder
Senior Member
 
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,868
The slab side was for ease of production. They shoot like any other open top Colt clone.



Along side a Dragoon.
madcratebuilder is offline  
Old April 14, 2013, 12:28 PM   #6
Roshi
Senior Member
 
Join Date: December 21, 2010
Location: Houston
Posts: 202
Thanks!

Thanks for all the replies.
Roshi is offline  
Old April 14, 2013, 01:38 PM   #7
bprevolver
Senior Member
 
Join Date: November 23, 2006
Location: Oklahoma
Posts: 133
Dance revolvers

Pietta has produced five different variations of the Dance revolver. These were first commissioned by Tony Gajewsky to produce the .36cal Dance revolver for Dance Firearms, Angelton, TX. and thus marked. Only thirty-five revolvers with the Dance Firearms markings were delivered. Pietta also delivered four prototype .44cal Dance revolvers marked Dance Firearms. These had rebated cylinders. A lawsuit over sales rights of the .36cal Dance revolvers prevents Pietta from ever making anymore .36cal revolvers.

A third variation was seventy .36cal Dance revolvers that were only marked with Pietta’s markings on the left side of the barrel. These were the last of the .36cal revolvers shipped to Tony.

Pietta continued producing the .44cal Dance revolver with rebated cylinder distributed though Dixie Gun Works. These had 7 ½” barrels. These were actually built on the 1851 Navy frame in .44cal. Re-enactors did not like these because of the rebated cylinder so Pietta redesigned the revolver with a shorter straight cylinder and an 8” barrel which is sold today though several distributors.

The original .44cal Dance Brothers revolvers were more the size of the Colt Dragoon but not as big making it larger than the .36cal 1851 Navy but smaller than the Dragoon making this particular revolver hard to fake.
bprevolver is offline  
Old April 14, 2013, 02:41 PM   #8
Hellgate
Senior Member
 
Join Date: November 18, 2010
Location: Orygun
Posts: 513
I have one and use it in Cowboy Action matches. It sure is easy to cap on the clock. I hated the Pietta Navt grips (too narrow at the top and too flared at the bottom) so I swapped them off for a set of Pietta Army grips. I pair it up with my 1860 Army. The shorter unrebated cylinder id drilled straight a bit deeper than the rebated Army cylinders. I can just get 30grs of FFFg under a wonder wad and a ball. With much shooting it is harder to ram home due to fouling build up in the chambers. I like mine but I've changed grips.

The second picture is me shooting my 1860 Army with the J H Dance laying on the table. Note the short cylinder and slab sided frame of the Dance. Sorry, I can't seem to enlarge that second photo to give a better look.
Attached Images
File Type: jpg JHDanceL.jpg (249.7 KB, 23 views)
File Type: jpg TrueGrit2012Smoke copy-1.jpg (27.3 KB, 22 views)
__________________
With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball.
SASS#3302 (Life), SASS Regulator, NRA (Life), DGB#129
Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell)

Last edited by Hellgate; April 14, 2013 at 02:54 PM.
Hellgate is offline  
Old April 14, 2013, 05:59 PM   #9
Roshi
Senior Member
 
Join Date: December 21, 2010
Location: Houston
Posts: 202
Thanks for the history BPRevolver!

I live less than an hour from the first Dance Bros. factory in East Columbia, TX. I posted pics of the site in an earlier post.

Dixie Gun Works lists a .44 with square back trigger guard while Cabelas have a .44 with round guard.
Roshi is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:48 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07859 seconds with 8 queries