The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools
Old April 11, 2013, 07:48 AM   #1
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 206
Otis cleaning kit for removing copper?

I have a new Tikka t3 Deluxe in 270 Win. I gave it a good cleaning before I fired it and cleaned it again after 7 rounds of Federal Power Shock 130gr. Both times I used a patch worm and Bore-Tek Eliminator. Since then I put 16 rounds of hand loaded Hornady SST 150gr through it. Well I since purchased an Otis cleaning kit and was wondering if it could be used to remove any copper fouling. I know, the brass brushes can be eaten by ammonia and was wondering if the brass patch holders would be damaged like the brushes when using ammonia based cleaners and patches? I also have a Pro Shot stainless steel rod and a universal Gun-Slick bore guide. Being a new barrel, I figured it might be a good idea to try and remove copper but don't want to use the Otis Kit if it will mess up the brass patch holders/threads and have one come off inside my bore. I plan to order some nylon brushes. Thanks for all advice!
p5200 is offline  
Old April 11, 2013, 08:51 AM   #2
wachtelhund1
Senior Member
 
Join Date: January 4, 2007
Posts: 141
You fill the barrel with the copper out solution to use the Otis system. After the barrel is clean, you empty the barrel of the solution and then dry patch and patch with oil. I've been using the Otis foul out system for 30 years, not even sure if it cantains any ammonia, if so it is a very small ammount and will not hurt your brushes.
wachtelhund1 is offline  
Old April 11, 2013, 11:25 AM   #3
L_Killkenny
Senior Member
 
Join Date: February 2, 2007
Location: Iowa
Posts: 2,676
So you've shot 23 rounds and you're worried about copper fouling?

Shoot it and quit worrying. Come talk to after you have 1000 or 2 rounds in the gun.
L_Killkenny is offline  
Old April 11, 2013, 12:31 PM   #4
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 206
Not worried by no means, just like to get an idea of how rough my barrels are when factory new. Being a Sako barrel I wouldn't think it would be extremely rough though. Thanks folks!
p5200 is offline  
Old April 12, 2013, 06:00 PM   #5
p5200
Senior Member
 
Join Date: April 1, 2008
Posts: 206
WOW! I guess the Otis kit is not much good for anything but powder residue and, rimfire use.
p5200 is offline  
Old April 13, 2013, 08:39 PM   #6
arizona98tj
Senior Member
 
Join Date: December 10, 2007
Location: Arizona
Posts: 975
I have a FNAR and use an Otis cleaning kit on it. I use the same cleaner on it as I do my bolts guns, that being Wipe-Out. It does a nice job on copper. The FNAR with the chrome lined barrel gets very little copper fouling, but the Otis patches do a nice job of cleaning what is there (and of course the powder fouling that accumulates).

Use your Otis kit....it will do the job.
__________________
stu-offroad.com
Largest Jeep TJ project site on the web!
(now with guns)
arizona98tj is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06303 seconds with 7 queries