The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Reply
 
Thread Tools
Old April 8, 2013, 09:19 PM   #1
ffs1942
Member
 
Join Date: December 14, 2010
Posts: 75
Simple Green as a gun cleaner?

What are the pros and cons of using Simple Green as a parts and bore cleaner?

We used it sometime in the Army
ffs1942 is offline  
Old April 8, 2013, 10:42 PM   #2
NESHOOTER
Senior Member
 
Join Date: October 16, 2009
Posts: 509
I personally have not had good luck with this, I would not chance it with any of my firearms, Hoppe's #9 is cheap.
NESHOOTER is offline  
Old April 8, 2013, 11:54 PM   #3
tahunua001
Senior Member
 
Join Date: July 21, 2011
Location: Idaho
Posts: 6,147
the only thing that was ever recommended for the M16 while I was in the Navy was good old fashioned CLP.

for people that shoot a lot of corrosive surplus they recommend windex, something to do with the amonia...

I would assume simple green would act in much the same manner.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar.
I never said half the crap people said I did-Albert Einstein
You can't believe everything you read on the internet-Benjamin Franklin
Bean counters told me I couldn't fire a man for being in a wheelchair, did it anyway. Ramps are expensive.-Cave Johnson.
tahunua001 is online now  
Old April 9, 2013, 12:00 AM   #4
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,117
Simple Green is hard on aluminum and should be rinsed soon.
Just another detergent improvisation on steel and plastic.
Jim Watson is online now  
Old April 9, 2013, 01:56 AM   #5
Powderman
Senior Member
 
Join Date: September 7, 2001
Location: Washington State
Posts: 2,160
I use a 50/50 mix of Simple Green and water in an ultrasonic cleaner for my guns. It will absolutely STERILIZE the gun--no carbon anymore, and it will also do a good job of loosening up the other fouling in the barrel.

Here's a caution, though--I also use an air compressor to blow all the parts dry, then I give them a good coating of WD-40, and let it sit for about an hour while I do other things. The WD-40 displaces any moisture left over.

I then wipe dry, and re-lube with a good medium weight oil.

Works great for me!
__________________
Hiding in plain sight...
Powderman is offline  
Old April 9, 2013, 03:34 AM   #6
mxsailor803
Senior Member
 
Join Date: February 8, 2010
Location: Norfolk, Va
Posts: 771
I used Simple Green on a surplus 91/30 covered in cosmo. It did ok there is other products that work better.
mxsailor803 is offline  
Old April 9, 2013, 09:08 AM   #7
Slopemeno
Senior Member
 
Join Date: January 19, 2007
Posts: 2,344
Simple Green and water was what we used in our parts washer in the gunsmithing shop I worked at. Worked great.

Don't leave blued parts soaking in it over the weekend though. Ask me how I know.

Seriously, it works great on duck guns that have two decades worth of unburned powder caked in the receiver.
Slopemeno is offline  
Old April 9, 2013, 02:28 PM   #8
Yung.gunr
Senior Member
 
Join Date: November 11, 2010
Location: Phoenix area
Posts: 1,377
I used it to clean the Cosmo off my 91/30. Other then that, nope not for my guns.
Yung.gunr is offline  
Old April 9, 2013, 05:35 PM   #9
ffs1942
Member
 
Join Date: December 14, 2010
Posts: 75
My SG CMP M1 saw service from 1943 into the 70's.

Seems in pretty good shape, but some rounds aren't ejecting far enough to chamber another round. I want to give the gas tube a good scrubbing.

I think we used Simple Green on M16's, M60's and M9's because it was "green" and CLP isn't. The federal govt is the first to suffer from its own stupid policies.

We continued to use CLP in the field. We used brake cleaner or hot water when we were lazy. We were even allowed to use a Safety Kleen sink, but that was 1 sink per 40 men.

I note that the bore cleaner that Beeman airguns sells is just Simple Green, but airguns have seals that are easily damaged by firearm products. I personally see no point in cleaning the bore of an unrusted airgun, even a match gun.
ffs1942 is offline  
Old April 9, 2013, 09:03 PM   #10
Ridge_Runner_5
Senior Member
 
Join Date: February 8, 2008
Location: Denver, CO
Posts: 1,888
There are tools designed specially for the purpose of cleaning the gas block. I'd really suggest buying that, rather than risking permanently damaging a classic firearm.
Ridge_Runner_5 is offline  
Old April 10, 2013, 08:50 AM   #11
Pacman
Member
 
Join Date: March 12, 2012
Location: Maryland
Posts: 34
Google "Ed's Red". It's a concoction of four ingredients that many use for cleaning guns. Inexpensive and good.
Pacman is offline  
Old April 10, 2013, 12:39 PM   #12
Railcar
Junior Member
 
Join Date: April 9, 2013
Posts: 13
I used it on my Cosmo 91/30, that was more grease than gun, Tried that afterr straight acetone wasnt doing the job either. Ended up running it through a dishwasher (dont laugh, it worked) with 2 cups of simple green and got rid of the cosmo, now on it is straight CLP
Railcar is offline  
Old April 10, 2013, 04:49 PM   #13
ffs1942
Member
 
Join Date: December 14, 2010
Posts: 75
Railcar, a dishwasher?

I've used a dishwasher on paintball gun parts and my old AMT Back-Up.

The dishwasher and normal dishwasher soap are tough on anodizing and plastic parts, but my only aluminum marker is a milsim (Tippman A5) and a rough patina on my vintage hopper looks good with the worn brassbrown finish of my only hopper fed Sheridan pump.
I might have run that marker through the dishwasher accidently once. No harm.

My AMT showed rust spots on its non stainless parts immediately, so I stopped that for all non stainless gun parts.

I use my dishwasher for anything from watches to Hot Wheels to litter boxes , though I might run it empty a few times after washing something nasty
ffs1942 is offline  
Old April 10, 2013, 06:29 PM   #14
csmsss
Senior Member
 
Join Date: October 24, 2008
Location: Orange, TX
Posts: 2,986
I'm personally not fond of any water-based cleaning solutions except for very specific purposes (ie removing corrosive salts after firing corrosive ammo).
csmsss is offline  
Old April 10, 2013, 08:01 PM   #15
Railcar
Junior Member
 
Join Date: April 9, 2013
Posts: 13
I didnt think it was an ideal solution either, but after 2 cycles with only simple green in the machine, I managed to remove all detectible cosmo, and after a couple thorough oilings, it has soaked up good clean gun oil and looks beautiful
Railcar is offline  
Old April 11, 2013, 08:09 AM   #16
Skans
Senior Member
 
Join Date: November 20, 2008
Posts: 7,865
I saw a video where someone used simple green and a bunch of 9v batteries in an anodizing process to give some titanium parts a gold colored coating. I'm thinking that's what Magnum Research uses on its titanium gold colored DE's.
Skans is offline  
Old April 11, 2013, 08:18 AM   #17
Madcap_Magician
Senior Member
 
Join Date: August 13, 2009
Location: MN
Posts: 619
I have used Simple Green to clean extremely dirty guns. Mostly crew-served after extended firing. Also, I did not own those guns. Worked well, but must be absolutely dried afterward if the gun has any aluminum parts.
Madcap_Magician is offline  
Old April 11, 2013, 09:16 AM   #18
Uncle Malice
Senior Member
 
Join Date: May 11, 2009
Location: Phoenix
Posts: 3,638
I've been using simple green for years, but only on full detail strip and cleans. Since it removes ALL lubrication residue... you want to be sure to thoroughly rinse, dry, and apply a light coating of oil back to the metal.

It was recommended through the AGI(American Gunsmithing Institute) training courses. It works very well and has caused no problems on any of my guns be it polymer, aluminum, stainless, etc. It's also non toxic and non abrasive to the hands, and doesn't smell terrible so you can use it inside.

I use RemOil after that for a light coating again. For actual lubrication points, I usually use MPro-7 or BreakFree CLP for oil - for sliding grease areas, such as on an AR BCG or 1911 rails, I'm a big fan of red axle grease(a little goes a long way).
__________________
Glock 17 G4 FDE | Glock 21 G4 FDE | S&W M&P 22 | S&W M&P 45 | S&W M&P 40 | S&W M&P 9 | Sig P226 MK25 | Sig P229 Extreme | HK P30 | HK45 | HK USP 9 | USP 45 TACTICAL | Springfield Armory XDM 9 OD
Daniel Defense DDM4 V4 | Arsenal SGL 21 | ASA SBR | Savage Mark II FV-SR | Mossberg 590A1 20" SP | Mossberg 500 Cruiser
My Instagram (mostly gun pics)
Uncle Malice is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10444 seconds with 9 queries