The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools
Old March 24, 2013, 02:56 PM   #26
KMAX
Senior Member
 
Join Date: June 20, 2011
Location: Texas
Posts: 1,053
Quote:
There are two things in this world I abhor, WD-40 and duct tape. Both have their place, but both are more often than not, the wrong tool for the job.
How can duct tape be wrong?
__________________
This is my gun. There are many like her, but this one is mine.

I'm not old. I'm CLASSIC!
KMAX is offline  
Old March 24, 2013, 03:17 PM   #27
Wreck-n-Crew
Senior Member
 
Join Date: March 8, 2013
Location: Ohio
Posts: 1,361
Quote:
That link is from a locksmith who states emphatically that WD-40 does not gum up, whereas he says 3 in 1 oil does. He says he's used WD-40 on locks for over 30 years with no problems. And if it won't gum up lock tumblers, it's a real safe bet that it won't gum up gun lock-work, as is commonly alleged.
You know when you mentioned this about locks i was told by a locksmith to use it liberally in an older model gm that wouldn't move. Surely enough i doused it inside and the key turned and never failed again. He said that we often deposit the buildup from our dirty keys in the tumbler every time we start the car and the WD-40 breaks the gunk down and walla!
__________________
If you ever have to use a firearm, you don't get to pick the scenario!
Wreck-n-Crew is offline  
Old March 24, 2013, 03:52 PM   #28
Lucas McCain
Senior Member
 
Join Date: March 7, 2013
Location: Callaway, MN
Posts: 187
I'm not going to go into the pro,s and con,s of WD-40. But I will address the subject of lubricants drying out,turning to varnish and gumming up mechanisms. This happens to all petroleum products, even fuels. But for this gumming up to happen, on its own takes a fair amount of time. Add dust and dirt, foreign material, and powder residue it speeds up the process but it will still be well over a year or two.
I then ask the question as to "'how often do you clean your guns? Not just the barrel or a wipe down. How often do you strip the gun down and really clean it?
Its a pro-active preventive maintenance schedule, instead of a re-active maintenance necessity because its gummed up. If you feel that your life depends on the reliable functioning of this gun, then you would be wise to set up a periodic maintenance schedule on it before it has time to gum up.
You change oil on your cars for the same reasons, only difference is the car has a drain plug, although sounds like a couple guns probably need one. I've never seen a gun with so much oil that the cartridges were ruined. " there"s your sign", not enough attention given to the gun.
__________________
If you have time to do it twice, then you have time to do it once right and put your name on it
Lucas McCain is online now  
Old March 24, 2013, 07:12 PM   #29
CurlyQ.Howard
Senior Member
 
Join Date: May 1, 2012
Posts: 280
Decades ago I had used WD-40 on my Remington 870 and all seemed fine. Then I went hunting in zero degree weather, and my 870 was frozen up. After than experience I have never again used WD-40 for any gun related purpose.
CurlyQ.Howard is offline  
Old March 24, 2013, 08:30 PM   #30
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,013
Thanks, Dan! I get tired of telling people about WD 40. I have used it for 40 years in the gun. knife, engraving, jewelry, music, and steam & refrigeration businesses.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old March 24, 2013, 09:41 PM   #31
Sgt Pepper
Senior Member
 
Join Date: August 19, 2001
Location: Texas
Posts: 698
I love WD-40. My grandpa would spray it on his feet and ankles periodically to loosen them up. He swore it worked! That aside, it will do well to clean metal up, but it is not a rust inhibitor and will do nothing to prevent corrosion. Many a garage engine builder has discovered that the WD-40 he sprayed and wiped his cylinder bores down with to keep them clean did preserve them as he though ti would when he returned some time later and found rust scaling up. WD-40 is a very SHORT TERM solution. It displaces water, and guess what, that water very likely ends up somewhere else on the firearm.
Sgt Pepper is offline  
Old March 24, 2013, 10:00 PM   #32
FoghornLeghorn
Senior Member
 
Join Date: September 2, 2011
Posts: 536
Quote:
that water very likely ends up somewhere else on the firearm.
Understood. I did my best to blow out the water (with the WD 40) from the mechanisms I couldn't get into to wipe dry. My objective was to displace the water to a location I could reach with a rag.

Next I soaked all the mechanisms/moving parts with Rem Oil. I let it sit and run out. I wiped it down again.

Then I soaked all moving parts with Hoppes #9 Lubricating oil. I let that soak for 8 hours or so, wiped it down, and reassembled the gun. I'll store it in that condition until my next range trip. Then I'll wipe the gun dry before I shoot it with the exception of the bolt.
__________________
"I say, boy, I say, you're doing a lot of choppin', but no chips are flyin'."
FoghornLeghorn is offline  
Old March 24, 2013, 10:25 PM   #33
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,013
Certainly WD 40 will prevent corrosion!
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old March 25, 2013, 09:09 AM   #34
Walt Sherrill
Senior Member
 
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 4,310
After reading Dan's posts and all the links, I'm no longer a disbeliever in WD-40. I may not use it much on my guns, as I have other stuff I think works better -- and I don't use a LOT of anything, a small bottle of various CLP-like products can last a long time -- but I'll be less concerned about warning people away from WD-40.
Walt Sherrill is offline  
Old March 25, 2013, 09:17 AM   #35
Skans
Senior Member
 
Join Date: November 20, 2008
Posts: 7,694
I always spray down my Savage 110 with WD40 after being out in the rain or snow with it after wiping it down with a towel. WD40 is a very good water disbursing agent.

Lubricating it is a different matter entirely - there are better things out there than WD40. However, a quick spray of WD40 in an AR to keep it running between magazines isn't going to hurt anything either.
Skans is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08065 seconds with 7 queries