The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 16, 2013, 03:51 PM   #1
jamaica
Senior Member
 
Join Date: March 24, 2006
Location: Northern Utah
Posts: 520
How to clean crimped primer pockets?

Just wondering what tools and techniques you use to ream those crimped primer pockets?
jamaica is offline  
Old March 16, 2013, 04:08 PM   #2
chiefr
Senior Member
 
Join Date: January 27, 2010
Location: AR
Posts: 1,294
The best way is to swage the crimp. RCBS makes a tool that will swage the crimp out using your press.
Dillon make the fastest one, but it will run you close to a hundred.
Some people use a deburring tool, I have used that method but if you are not carefull, you can remove too much brass.
chiefr is offline  
Old March 16, 2013, 04:49 PM   #3
serf 'rett
Senior Member
 
Join Date: June 25, 2009
Location: Stuttgart
Posts: 1,387
^ That's pretty much the summation of the matter; however, I happen to know a wood countersink will work if used judiciously.
__________________
A lack of planning on your part does not necessarily constitute an emergency on my part.
serf 'rett is offline  
Old March 17, 2013, 12:44 AM   #4
A pause for the COZ
Senior Member
 
Join Date: October 11, 2012
Location: Braham, Minnesota
Posts: 402
There are many ways to remove the crimp. I use the RCBS primer pocket swaging combo. Comes with a large and small swage rod.
It works well enough, Maybe 90% of the brass swaged it does fine.

One particular brand of brass is difficult no matter what. I purchased a 1000 Speer 223 cases a couple years ago.
Its great brass for reloading, but the primer pocket makes you pay for that privilege.
The swager would remove the crimp just fine, but this brass has a tight pocket with very sharp edges. Gives you lots and lots of damaged primers.



Solution to that problem and can also be used by its self to remove primer crimps on any brass. Is you chamfer (sp) tool.
Just spin it in the pocket a couple times and out comes the crimp.



You end up with a nice rounded edge primer pocket.



Oh one thing you want to do. Mark your brass after you process the primer pockets. You only need to do it once. After a range visit you will be surprised how much extra 223 brass you come back with. Makes sorting them easy.
Mark = Goes in the tumbler no mark = goes in the to be processed pile.

A pause for the COZ is offline  
Old March 17, 2013, 01:20 PM   #5
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 12,638
I just buzz them off with a wood countersink on my cordless drill. Using that Lee tool in the picture is fine for a few cases, but when you have 400 to process you'll want a power tool.
chris in va is offline  
Old March 17, 2013, 03:01 PM   #6
wncchester
Senior Member
 
Join Date: December 1, 2002
Posts: 2,832
A Lyman primer crimp reamer chucked in a portable electric drill has done nice work for me for some 30 years. I refuse to use a counter sink or drill bit for that work because they remove too much metal to get below the crimp and that leaves more unsupported primer cup than I'm comfortable with.
wncchester is offline  
Old March 17, 2013, 03:01 PM   #7
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,797
Five posts and nobody has mentioned the primer pocket crimp reamer?

Made by several reloading tool makers, it's simply removes the crimp by cutting it;

http://www.midwayusa.com/product/253...ter-head-small

http://www.midwayusa.com/product/435...-accessory-set

It cuts until the end bottoms out on the bottom of the pocket. Makes sure it doesn't cut too much brass from the edge of the pocket.

The swaggers are supposed to do a better job, to each his own. My cutter like the above is mounted in my RCBS case prep center. Takes about 2-3 seconds, DONE!

I call that tie! Wnchester posted at the same time!
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old March 18, 2013, 12:20 AM   #8
primerman
Senior Member
 
Join Date: December 23, 2011
Posts: 129
I have one made by some company in Nebraska and it works just fine for no more crimped brass than I run across. I guess if I had to do a lot i'd consider something else, maybe in green.
primerman is offline  
Old March 18, 2013, 08:36 AM   #9
hunter52
Senior Member
 
Join Date: January 27, 2011
Location: Colorado
Posts: 100
I have the Lyman hand reamers which work really well and are quick, I also have the cutter attachment for Forsters trimmer which cuts quick and is easily set to eliminate cutting too much.

If I am prepping a large batch of brass it's the Forster, for a handful or so I like the Lyman.
hunter52 is offline  
Old March 18, 2013, 08:58 AM   #10
Magnum Wheel Man
Senior Member
 
Join Date: July 26, 2006
Location: Southern Minnesota
Posts: 8,535
I use the "old style" RCBS unit that goes into a single stage press... I see RCBS offers one that is the Dillion style, so they have 2 styles now... I think the new style is free standing, & built for those using progressive presses

personally I like the "idea" of swagging better than reaming, as you aren't removing any brass from the base of the cartridge...
__________________
In life you either make dust or eat dust...
Magnum Wheel Man is offline  
Old March 18, 2013, 10:32 AM   #11
schmellba99
Senior Member
 
Join Date: January 8, 2008
Posts: 606
While I'm not normally a Dillon homer, they make a hell of a good primer pocket swager. Lord only knows how many thousands of rounds have run through mine without any issues.

No power, no cutting, no need for an extra step of counter sinking the pocket after the reamer is done - just pull the handle and onto the next round.

May be a little expensive, but there are pretty much no parts that will break, need sharpening, need replacing, no power requirements, etc, etc, etc.
schmellba99 is offline  
Old March 23, 2013, 01:06 AM   #12
Dwayne
Member
 
Join Date: February 2, 2012
Posts: 23
Here is another tool to add to the toy box: $31.58.

http://www.ch4d.com/catalog/primming/419000
Attached Images
File Type: png 419000-icon.png (46.8 KB, 8 views)

Last edited by Dwayne; March 23, 2013 at 01:32 AM.
Dwayne is offline  
Old March 23, 2013, 01:24 AM   #13
ScottRiqui
Senior Member
 
Join Date: January 27, 2010
Location: Norfolk, VA
Posts: 2,905
I have the Dillon swager, and it works great. The only problem I discovered with it early on is that if I set it to remove absolutely ALL traces of the crimp, I sometimes have trouble getting the swaged case into and out of my press' shell holder.

It makes sense, because the swaged metal has to go somewhere, and you can end up with the area surrounding the primer pocket no longer being perfectly flat.

All I did was adjust the tool to not swage quite as much. Rather than obliterating any sign of the crimp, I just swage it enough to "break" the edge of the crimp, slightly rounding off the transition from the flat part of the case into the primer pocket. The new primers still go in nice and easy, and I don't have to fight the case into the shell holder.
ScottRiqui is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09948 seconds with 8 queries