The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 15, 2013, 06:27 AM   #1
rebs
Senior Member
 
Join Date: January 10, 2012
Posts: 2,240
45 acp 200 gr lswc ?

I load 45 ACP 200 gr lswc for target shooting. I I crimp 4.069 at the case mouth and OAL of 1.250. What is the procedure to setup the die to seat and crimp in one operation without shaving lead, instead of using a separate crimp die?
I am not crimping in a crimp groove.
rebs is offline  
Old March 15, 2013, 09:47 AM   #2
steve4102
Senior Member
 
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,226
Quote:
I crimp 4.069
Obviously a typo, but what do you really crimp to?

.4069 or .469?
steve4102 is online now  
Old March 15, 2013, 10:04 AM   #3
rebs
Senior Member
 
Join Date: January 10, 2012
Posts: 2,240
I crimp to .469
rebs is offline  
Old March 15, 2013, 10:13 AM   #4
trixter
Member
 
Join Date: February 27, 2011
Location: Where E. Pine St. crosses I-5
Posts: 38
Well... Let see, I use Lee dies on my Classic Turret press. I use a crimp die, however in the instructions with the die set it explains how to use the seater die to both crimp and seat. It reads fairly straight forward. Go to the Lee site and look up the instructions for setting up the dies. If you need more info let me know.
trixter is offline  
Old March 15, 2013, 05:32 PM   #5
EmptyHull
Senior Member
 
Join Date: March 29, 2009
Posts: 145
I have found that I prefer to use separate seating and crimping stations. I have done both but settled on doing it like this. Tim
__________________
uva uvam videndo varia fit
EmptyHull is offline  
Old March 15, 2013, 10:35 PM   #6
Miata Mike
Senior Member
 
Join Date: May 22, 2010
Location: North East WI
Posts: 417
3rd stage Seating/Crimping die adjustment for Lee die

With an empty case in the shell holder, raise the ram to the top and turn the die in until it stops. This is where the crimp shoulder meets the case.

Place a bullet on the empty flared case. Raise and lower the ram checking bullet seating depth. (make sure the adjustment knob is backed off some first)

Rotate the adjustment knob clockwise while holding the die. Raise and lower the ram to confirm seating depth.

Lower the ram and turn the die in one additional half turn. Raise the ram to complete the crimp depth. You might have to fine tune you crimp by raising or lowering the whole die a fuzz.

I don't use the Lee factory crimp die any more on handgun loads.
__________________
NRA Life Member.
Miata Mike is offline  
Old March 16, 2013, 12:21 AM   #7
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 12,542
The 45acp doesn't need a taper crimp. Just set the die so it removes the flare.
chris in va is offline  
Old March 17, 2013, 10:49 AM   #8
bluetopper
Senior Member
 
Join Date: December 16, 2005
Location: Paris, TX
Posts: 1,104
I never measure my crimp.......crimp till it falls in the chamber freely. Your barrel chamber should be your guage.
__________________
I use Liberal tears as gun lubricant.
bluetopper is offline  
Old March 17, 2013, 12:31 PM   #9
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,731
My 1911 and camp carbine don't like Extreme's plated 200gr SWC. To get this bullet to run in these guns I seat at 1.230" and TC crimp to .469-.470"
joneb is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06900 seconds with 7 queries