The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 14, 2013, 08:47 PM   #1
Latesvak
Junior Member
 
Join Date: March 29, 2012
Posts: 4
need help w/ kids gun

So I have a extra ruger 10/22 stock and I would like to know how to go about cutting it down to properly fit my daughters grip . This will be twice as nice because I also have twin boys who will eventually use this as well. I'm pretty good with tools so that's not a problem but just trying to see if anyone has done this or has any good pointers. She's excited to go shooting with daddy but can't till she gets the rules down first. And has a stock to fit. I should mention this is only going to be for target practice and bench shooting.

Luke
Latesvak is offline  
Old March 14, 2013, 09:20 PM   #2
Onward Allusion
Senior Member
 
Join Date: November 17, 2009
Location: IN
Posts: 1,763
You may want to look into getting a new stock instead of cutting one down, unless you're into woodworking.

Blackhawk Axiom... Collapsible 6 position that will grow with your child. It will also take almost a pound off the rifle. Don't forget to get the cheek piece. It also free floats the barrel.
__________________
"With great power, there must also come great responsibility." - Stan Lee

"All that is necessary for evil to triumph is for good men to do nothing." - Edmund Burke
Onward Allusion is offline  
Old March 14, 2013, 11:59 PM   #3
nanewt02
Senior Member
 
Join Date: February 25, 2013
Posts: 248
Clamp the portion of the stock you want cut off snugly in a vice and have your cutting line level with the top of the vice jaws, using a fine blade handsaw, cut your stock moving across it slowly, obviously you will be holding it sideways since your cut line is horizontal keep a small downward force and a very very slight downward angle on the blade even pressure on both sides of stock, your blade should skate across the top of the vice jaws giving you a nice even cut. Use same direction only stokes with rough grit sand paper wrapped on 2 by 4 block to sand out any imperfections
nanewt02 is offline  
Old March 15, 2013, 09:24 AM   #4
TATER
Senior Member
 
Join Date: November 19, 2002
Location: Mississippi
Posts: 933
Just got the Wife this one, it turned out nice.

http://www.brownells.com/rifle-parts...1=Ruger__10/22
TATER is offline  
Old March 15, 2013, 07:11 PM   #5
oneoldsap
Senior Member
 
Join Date: September 16, 2009
Location: I live in the foot of the Green Mountains of Vermont
Posts: 1,588
If you have access to a power Mitre saw , just make sure your stock is laying square on the table when you make your cut . Then try for fit . A shower shoe , makes a nice economical pad for it too . Just trace , cut and glue on ! Contact cement works great . Oh and don't worry about finding another wood 10-22 stock , they are a dime a dozen , every gun shop has a few laying around , as so many were replaced with synthetics .
__________________
Don't forget to have your liberals spayed or neutered !
oneoldsap is offline  
Old March 16, 2013, 03:30 AM   #6
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,925
Others respondEd to shortening the stock. I'd reach for a #49 Nicholson file and rasp the grip down. Then scrape it smooth until it feels comfortable to the daughter. I would also slim down the rest of the stock.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old March 16, 2013, 08:19 PM   #7
oldgunsmith
Senior Member
 
Join Date: January 9, 2013
Posts: 278
With her hand on the grip and her finger on the trigger and her elbow bent at about 45 degrees, how far does the butt come from comfortably fitting in to the bend in the elbow? If she has to stretch and strain to get it there, she may be more comfortable with a little shorter length of pull.
oldgunsmith is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07067 seconds with 7 queries