The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 26, 2013, 10:16 PM   #1
t45
Senior Member
 
Join Date: January 29, 2010
Location: Belews Creek, NC.
Posts: 599
Small pistol primers vs small pistol magnum primers

I can't seam to find regular small pistol primers anywhere. I did run acrossed some small pistol magnum primers. What is the down side if I backed off the charge weight by a few tenths? Just asking. Not sure I feel comfortable going down that road.
t45 is offline  
Old February 26, 2013, 10:26 PM   #2
Budweiser
Member
 
Join Date: August 1, 2009
Location: Minnesota
Posts: 20
I inadvertently bought a brick of Winchester Magnum Small Pistol primers, I don't have a .357 Mag to use them on, so I have been working up a load to use them with small primer 45ACP cases, which I have about 1000 of also.
Budweiser is offline  
Old February 26, 2013, 11:38 PM   #3
fehhkk
Member
 
Join Date: September 17, 2011
Posts: 16
Small pistol primers vs small pistol magnum primers

I have loaded 40S&W with 185gr FMJ with CCI 550 magnum SPP. No problems. I used 4.9-5.0 gr of Bullseye for these along with 1.10" OAL, just perfect. I backed off the load by 0.4gr of what I normally do with regular primers.
fehhkk is offline  
Old February 26, 2013, 11:46 PM   #4
Misssissippi Dave
Senior Member
 
Join Date: December 5, 2009
Posts: 1,407
Back off the load about 10% and work it back up again. This should get you close depending on the caliber, bullet and powder combination.
Misssissippi Dave is offline  
Old February 26, 2013, 11:49 PM   #5
j357
Senior Member
 
Join Date: January 25, 2009
Location: Liberty Twp, OH
Posts: 220
Google and the search feature at the top of this page are your friends. You will find various recommendations to reduce charge by percentage weight. I bought 700 SPM about 2 months ago as I was fearful that would be all I could find. I came across a deal from a local friend 2 days later that included 1K regular SPP primers so I have not put the search results to use yet, but plan some small work ups in 38 and 9mm later this summer.

On second thought, I may hold them until I purchase a .41 Magnum in a year or two.
j357 is offline  
Old February 27, 2013, 02:39 PM   #6
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,340
Personally, I would keep them for something like a .357 mag....or trade them to someone that wants them for standard small pistol primers...

But you can probably get away with dropping the powder down toward the Minimum published recipe ( and shoot them in a steel gun, with a fully supported chamber )...!
BigJimP is offline  
Old February 28, 2013, 06:01 AM   #7
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 8,771
I see at least three different references to using magnum primers in .357 or .41 "Magnum."

Gotta realize that "magnum" is just a cartridge name. It's supposed to give everyone within earshot the idea that it's a balls-to-the-wall rhino killer, but it's still just a name. The .32 H&R "Magnum" should have been called a "special."

The point: you don't need magnum primers simply because it's a "Magnum" load. Magnum primers are called for because of the powder, not because of the funny name stamped in to the case head.

For sure, you can use magnum primers in any load, but there's no easy, "across the board" reduction schedule. Simply put, you reduce your load and work back up to where you want to be. Safely, using proper handloading techniques.

But as long as you are working with powders that don't demand magnum primers (like H110), you simply don't need magnum primers. You could load a dizzying array of .357, .41 and .44 Magnum loads and never use a magnum primer.

There's been a lot of folks who've expressed that Hercules/Alliant 2400 runs all of it's loads better with standard, non-magnum primers. 2400 was -THE- go-to powder for handloading .357 Magnum for decades and still does a phenomenal job of it.

I've been loading all three of those well-known "magnums", and .38 Super and 10mm and I've never, not once ever purchased a magnum primer in my entire life. Never once primed a case with a magnum primer.

My plan is to NEVER buy one.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06581 seconds with 7 queries