The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 23, 2013, 01:22 AM   #1
bodieBill
Member
 
Join Date: March 9, 2005
Location: Southern California---no not LA
Posts: 24
45 ACP

Puzzled.
Reloading some previously fired 45 ACP brass.
Most cases reloaded and chambered OK; several did not.
I checked the following and all within specs
Brass length Ok
full length re-sized
Bullet diam Ok
OAL within specs
Used Lee factory crimp tool with out crimping as afinal gauge which I do with all my semi auto rounds
The cases that would not fully chamber in my 1911 barrel used as a gauge
had some interference when going thru the carbide ring of the Lee crimp die
The full length resized brass went into the barrel chamber ok.
Could it be the wall thicknes of the brass neck??
Advice welcomed
bodieBill is offline  
Old February 23, 2013, 01:23 AM   #2
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 12,493
Be more specific... Bullet type/brand, oal etc.
chris in va is offline  
Old February 23, 2013, 02:09 AM   #3
shootniron
Senior Member
 
Join Date: April 16, 2011
Posts: 1,147
Is this range brass or did you previously fire it in the 1911?

If they are in spec, as you say, they should chamber...something is out of spec somewhere. Are you sure there is not a bulge at the base of the bullet when it is seated?

Last edited by shootniron; February 23, 2013 at 03:50 AM.
shootniron is offline  
Old February 24, 2013, 12:14 AM   #4
bluetopper
Senior Member
 
Join Date: December 16, 2005
Location: Paris, TX
Posts: 1,099
Crimp it more with your Lee seating/crimp die before you use your Lee factory crimp die.

If your crimp die is adjusted properly you really don't need the factory crimp die.
__________________
Uprisings started or quelled. Tornadoes rerouted.

Last edited by bluetopper; February 24, 2013 at 12:35 AM.
bluetopper is offline  
Old February 24, 2013, 12:52 AM   #5
TXGunNut
Senior Member
 
Join Date: January 16, 2010
Location: If you have to ask...
Posts: 2,851
Specs? The only specs with the 45acp that count are the plunk test. If you'll use the plunk test and a taper crimp die I think your reload problems will evaporate like a politician's promises after election day.
__________________
Life Member NRA, TSRA
Smokeless powder is a passing fad! -Steve Garbe
I hate rude behavior in a man. I won't tolerate it. -Woodrow F. Call Lonesome Dove
My favorite recipes start out with a handful of used wheelweights.
TXGunNut is offline  
Old February 24, 2013, 08:50 AM   #6
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 2,787
Quote:
...The cases that would not fully chamber in my 1911 barrel used as a gauge
What is the case mouth diameter of the loaded rounds?
It should be 0.471 ± 0.001 (or so)
mehavey is offline  
Old February 24, 2013, 09:44 AM   #7
chiefr
Senior Member
 
Join Date: January 27, 2010
Location: AR
Posts: 1,177
Have seen this before and what we found was the sizing die was not fully sizing the cases.

The carbide sizing die was not fully sizing the case because it was bulged. The carbide die was part of the problem because of its inside taper. The distance of the inside taper to the base of the seating die was enough that it would not size out all of the bulge.

Some pistols are notorious for bulging cases. Lee makes a bulge buster die which will take care of things.
I thought I might add to watch primer pockets when reloading 45ACP. Seems some manufacturers are making brass with small primer pockets.
chiefr is offline  
Old February 25, 2013, 11:43 AM   #8
maillemaker
Senior Member
 
Join Date: August 30, 2010
Posts: 994
All of my finished .45 ACP cartridges have a slight bulge in the brass where the bullet terminates. My bullets are obviously bulging the brass as they are seated.

I could use a Lee FCD to re-size the brass after seating/crimping, but I have not found this necessary yet. Also it is said that doing so is actually deforming/resizing your bullet.

Steve
maillemaker is offline  
Old February 25, 2013, 02:06 PM   #9
chiefr
Senior Member
 
Join Date: January 27, 2010
Location: AR
Posts: 1,177
I taper crimp all my 45ACP with a Lee taper crimp die (TCD). The TCD is in the final die station on my Dillon. TCD all auto pistol brass. Never used or tried a FCD. Love the TCDs as I have never had a headspace problems.
chiefr is offline  
Old February 25, 2013, 03:33 PM   #10
Budweiser
Member
 
Join Date: August 1, 2009
Location: Minnesota
Posts: 20
Check the rims for nicks that may be causing you problems?
Budweiser is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08347 seconds with 7 queries