The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old February 6, 2013, 01:17 AM   #1
mr kablammo
Senior Member
 
Join Date: December 18, 2005
Posts: 241
Ithaca M37 disassemble and reassemble

How difficult is it to break down a M37 for a part-by-part cleaning and to reassemble? This looks to be of the 'fitted barrel' era. Were guns of that time blued or rust blued?
__________________
"America is a free country, and Michael Moore is free to make an @zzhole of himself". David Horowitz in "Michael Moore Hates America".
mr kablammo is offline  
Old February 6, 2013, 01:31 AM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,504
An Ithaca M37 is not difficult to break down completely. It is actually quite simple once you know how. I recommend a good disassembly/assembly manual, most have pictures and instructions for the M37. M37s were caustic blued or phosphated.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old February 6, 2013, 07:22 AM   #3
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,235
They're not particularly complex, but when you are reassembling them they can be a bit fiddly getting everything to line up properly.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old February 6, 2013, 08:44 AM   #4
jaguarxk120
Senior Member
 
Join Date: February 28, 2008
Location: Michigan
Posts: 1,969
If you go to www.shotgunworld.com and in the Ithaca forum you can find the Model 37 take down guide. The guide is actually in steves pages but the forum is a direct link to it.

Please note when taking down the Model 37 the butt stock MUST be removed before trying to disassemble the action. Pressure from the stock locks the triggerplate screw in place as if it was loc-tited in to place.

You will find that the Model 37 has less parts than any other pump gun made. This all go's back to when the gun was designed. Original concept was from JM Browning and then improved at Ithaca.
jaguarxk120 is offline  
Old February 6, 2013, 01:56 PM   #5
drcook
Senior Member
 
Join Date: November 25, 2009
Posts: 240
there is a bolt with a slotted head in the Ithaca butt stock. When ever I need to take mine off, I take a driver bit and tape it into a 1/4 driver socket. Then I wrap masking tape around the socket until it is built up just enough so slip into that access hole. The tape will keep the bit in the slot.

There is also the possibility you might have a socket that will fit the stock bolt also. Regardless, trying to do it with a screw driver is a definite PITA.
drcook is offline  
Old February 8, 2013, 07:59 AM   #6
CaptainChaos
Member
 
Join Date: November 8, 2011
Location: Hampshire, UK
Posts: 37
When I took up shotgunning, I had a lot of trouble with the stock coming loose. I, too, found using a screw-driver awkward.

But, it's a slotted hex bolt head and I found that using a nut-driver *much* easier. In the event, I made a special "M37 Stock-Driver".

Take a length of, say, 8mm bar. Grind a 1/4" square on each end. On one end, fix a 3/8" (or whatever it was) socket. On the other, a Philips / Pozidriv / whatever screw-driver bit for the two butt-plate screws. Finally, weld a short length of bar at right-angles near the screw-driver bit. Et, voila! A tool that makes things *much* easier.

What's really annoying is that my stock cracked and so I acquired a Choate plastic stock; the hex head is a different size thus making my tool useless...

Regards,

Mark.
CaptainChaos is offline  
Old February 8, 2013, 10:07 PM   #7
barnbwt
Senior Member
 
Join Date: May 17, 2012
Posts: 733
Saw this and thought some diagrams I made earlier for my M90 build were pertinent:


I missed the safety detent-pin and spring. They're tiny, and sit on the left side of the trigger plate above the safety in a tiny little hole--don't lose them when you pop out the safety! Oh, and my 1976 has a bolt with a square head for some stupid reason. Luckily I managed to find a metric socket that grabbed enough to break it loose.

I'm no gunsmith, so my terminology is bogus, but hopefully these will help you out. It's always a good idea to document dissassemblies like this with photos to help retrace your steps

Here's the build so far (and my 700 SPS destined for a FAL magazine); got the dummy-stock inletted for the modified trigger/bolt release controls:


TCB
__________________
"I don't believe that the men of the distant past were any wiser than we are today. But it does seem that their science and technology were able to accomplish much grander things."
-- Alex Rosewater

Last edited by barnbwt; February 8, 2013 at 10:26 PM.
barnbwt is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:21 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08327 seconds with 9 queries