The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 7, 2013, 07:49 PM   #1
FloridaGuy
Senior Member
 
Join Date: December 8, 2012
Location: Clearwater, FL
Posts: 166
Tumbled Range Brass

This is the first time that I am using range brass. So I just tumbled several thousand rounds of .38 special brass. I used crushed walnut media in the tumbler. There seems to be some of the media stuck inside of the cartridges. What is the best way to get all of this out of the cartridge? Or is it ok to load these cartridges if there is still small amount stuck to the walls of the case?
FloridaGuy is offline  
Old February 7, 2013, 07:54 PM   #2
grumpa72
Senior Member
 
Join Date: April 5, 2009
Posts: 459
I take a small flat head screw driver and scrape the walls when I see media stuck in there. It is NOT ok to reload with media there because that will increase the case pressure beyond what you are reloading for and expecting. The inside of the case should be free of debris.
grumpa72 is offline  
Old February 7, 2013, 08:08 PM   #3
SVO
Senior Member
 
Join Date: December 20, 2009
Location: Texas Gulf Coast
Posts: 665
:
Lee makes a punch for removing crimped primers from military brass. The punch for a 223/5.56 case works great to remove any media stuck in the primer pocket/primer flash hole.
SVO is offline  
Old February 7, 2013, 08:18 PM   #4
1Hobie
Senior Member
 
Join Date: November 6, 2010
Location: west central Illinois
Posts: 272
Take out the media and retumble the brass. The remaining bits should come out. If not, maybe you're using a tad bit too much compound in your media.

Hobie
1Hobie is offline  
Old February 7, 2013, 09:11 PM   #5
GP100man
Senior Member
 
Join Date: August 1, 2007
Location: Tabor City , NC.
Posts: 1,914
"maybe you're using a tad bit too much compound in your media."


This is exactly what I was thinkin !

If to much additives to the media it`ll clump & cling to places we don`t need it to .

Try takin the top off & letting it dry while running a bit .

Even if it don`t feel damp ,it`s damp enuff to clump/cling.
__________________
GP100man
GP100man is offline  
Old February 7, 2013, 10:11 PM   #6
Jay24bal
Senior Member
 
Join Date: December 13, 2011
Location: Cleveland, OH
Posts: 606
Do you own an air compressor?

I find that an air compressor works very well to blow any debris out of a case. It also works well to dry the cases if you use an ultrasonic cleaner. I have a small "pancake" compressor that sits next to the workbench for other things, and it often times gets called into duty for this as well.

While not nearly as cost effective, the cans of compressed air for electronics will also accomplish the same job.
__________________
I like guns.

Once Fired Brass, Top quality, Fast shipping, Best prices.
http://300AacBrass.com/ -10% Coupon use code " Jay24bal "
Jay24bal is offline  
Old February 7, 2013, 11:12 PM   #7
Misssissippi Dave
Senior Member
 
Join Date: December 5, 2009
Posts: 1,405
Sounds like an additive to the media was not fully mixed in before adding the brass. That happens fairly often to people using an additive the first time or two. I would scrape out the cases and put them back into the tumbler for a while to let them get cleaned out. Don't put any additive in this time around. Any media stuck inside the case will reduce the volume and increase the pressure just like seating the bullet deeper would. It is a good thing you caught this problem prior to loading the cases.
Misssissippi Dave is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08318 seconds with 7 queries