The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 31, 2013, 07:14 AM   #1
poline
Senior Member
 
Join Date: January 27, 2009
Location: Richmond,Va
Posts: 292
Bullet Dia.

I'm wondering if I can use the .452 dia.
Guardian Gold Jackted pistol bullet in 185gain JHP
in the 45 colt. (New Ruger Vaquero) My concern is the Dia of the bullet because it is Jackted.This would be a self defense load. What do you think?
Any replys are appreciated.
poline is offline  
Old January 31, 2013, 02:13 PM   #2
SL1
Senior Member
 
Join Date: November 8, 2007
Posts: 1,994
A lot of the new Rugers will not allow .452" diameter bullets to enter the cylinder throats. Mine allowed .450" gauges until it had been fired about 100 times, then allowed .451" bullets.

But, so long as the bullets are seated deeply enough so that they do not have to have their full diameter actually enter the cylinder throats, they will work fine. When fired, they simply swage down to throat diameter.

With a 185 grain bullet that is designed for a .45 ACP auto-loader, it should be easy enough to seat the bullets deeply enough to work just fine.

SL1
SL1 is offline  
Old January 31, 2013, 08:41 PM   #3
GeauxTide
Senior Member
 
Join Date: April 20, 2009
Location: Helena, AL
Posts: 3,036
Ruger still makes a convertible Blackhawk. Mine measured .4515. My Bisley Blackhawk measures .452. I don't see how firing cast or jacketed bullets will open a cylinder throat .001.
GeauxTide is offline  
Old February 1, 2013, 03:39 PM   #4
SL1
Senior Member
 
Join Date: November 8, 2007
Posts: 1,994
Gauxtide,

As I posted before, the throats opened enough to accept the next sized plug gauge. Whether that is more or less than 0.001" is hard to say, since the gauges are graduated in steps of 0.001".

But, it was darned clear that the cylinder throats opened some with firing less than 100 rounds of Federal "Champion" .45 ACP ammo. That is the Walmart cheap stuff with thick-plated 230 grain TMJ bullets (that turned out to be as much as 0.004" out-of-round) and cases with small pistol primer pockets.

Another 100 rounds did not get them to 0.052, so I am assuming that I was polishing-off some surface roughness, and maybe peening the surfaces a bit. I usually do this with revolvers to make sure that the barrel threads are fully forced-out into the frame threads before I start looking for any barrel constriction to remove.

SL1
SL1 is offline  
Old February 2, 2013, 11:08 PM   #5
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
Send it to Cylindersmith. They'll open the chamber throats up to .4525 and life will be good then.

http://www.cylindersmith.com/
Edward429451 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06220 seconds with 9 queries