The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 2, 2013, 05:14 PM   #1
nistech95
Junior Member
 
Join Date: January 26, 2013
Posts: 9
.452 plated bullets in 1911

Went by the LGS today and he had some Berry's .452 230gr RN bullets at a pretty fair price. I am wanting to load these for my 45 acp Colt 1911. I am confused on the .452 diameter though. I haven't loaded 45acp before but i have experience in other pistol and rifle calibers, none in a semi auto pistol? Due to the lack of .451 bullets available I picked these up on a whim. Before I go any further with this I wanted some insight from some more experienced loaders. Thanks for the help in advance.
nistech95 is offline  
Old February 2, 2013, 05:55 PM   #2
arch308
Senior Member
 
Join Date: November 6, 2011
Location: DFW, Texas
Posts: 876
I use Berry's almost exclusively nowadays for my 45 ACP. For the price they are excellent bullets. I tend to use their 185g HBRN. Just load them like you would any jacketed bullet, at least in the 45 ACP.
arch308 is offline  
Old February 2, 2013, 06:12 PM   #3
Adamantium
Senior Member
 
Join Date: June 6, 1999
Location: El Paso, TX
Posts: 981
Berrys recommends staying below 1200fps but that is really the only caveat. Otherwise load them using regular jacketed bullet data. The .452 vs .451 is not an issue in the slightest.
__________________
New gun, same ol' shot.
Adamantium is offline  
Old February 3, 2013, 09:07 AM   #4
steve4102
Senior Member
 
Join Date: December 23, 2005
Location: Minnesota
Posts: 2,137
Berry's are sized to .452 same as Lead bullets. You purchased the correct size for your 1911.
steve4102 is offline  
Old February 3, 2013, 11:13 AM   #5
testuser
Senior Member
 
Join Date: September 8, 2010
Posts: 495
If the bullet is oversized, then I refrain from using my Lee Factory Crimp die. It tends to swage the bullet down. I just give them a really light taper crimp, usually crimping and seating in the same step.

You'll have to experiment with the load. I find starting loads or just above starting loads for jacketed data works best for many calibers, but you'll probably want to start with lead data and definitely not exceed mid range jacketed data.
testuser is offline  
Old February 3, 2013, 03:25 PM   #6
jag2
Senior Member
 
Join Date: June 30, 2009
Location: dallas
Posts: 378
What everyone has said. Just be careful with the crimp, you don't want to crack the plating or you will get separation even with low charges.
jag2 is offline  
Old February 3, 2013, 03:36 PM   #7
wyobohunter
Senior Member
 
Join Date: August 21, 2008
Location: Back in Wyoming
Posts: 1,125
I use these bullets as well. I called Berry's when I first started, they told me I should load 1/2 way between lead and jacketed data.
wyobohunter is offline  
Old February 3, 2013, 05:17 PM   #8
gandog56
Senior Member
 
Join Date: May 31, 2006
Location: Mobile, Alabama
Posts: 964
My Lee Modern Reloading Second Edition is the only manual I know that has copper plated bullet recipes. Thinking that they are also on the manual included in the newer lee die sets. My die set is too old for those.
__________________
Some people think I'm paranoid because I have guns. If I have guns, what do I have to be paranoid about?
gandog56 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08877 seconds with 9 queries